Increase the stitch length to 4, set needle thread tension to 0, and sew a basting stitch (_ the entire length of the zipper opening. 34 Posici6n variable de la aguja Position variable de I'aiguille AI seleccionar la puntada recta (patr6n 1), usted puede mover la Lorsque f'on a choisi le point droit (motif 1), il est possible de aguja entre la posici6n central e izquierda de Ia aguja, girando ta positionner I'aiguille au centre ou _-gauche au moyen du cadran perilla de anchura de puntada, de r_g

Select pattern 30. Press the ._i. key. Select pattern 30. Start to sew. The machine will sew the pattern combination repeatedly. Notes: • If you press the auto-lock button in the middle of a programmed pattern, the machine will stop automaticall_ after the current pattern is completed. • The stitch image on the visual touch screen may not represent the accurate sewing result in some cases. J 47 Programming French Knot Example: pattern 51, 39, 40 Stitch pattern: 51, 39, 40 Needle thread tension 3

TABLE OF Section CORITEr_TS Section Section Section i Knowing Your Sewing Machine Identifying Parts Installing Machine Converting to Free-arm Sewing Winding the Bobbin Threading the Bobbin Case Threading of Top Thread Using the Controls Adjusting Top Tension Adjusting Bobbin Tension Checking Tensions Stitch Width Control Stitch Length Controf Reverse Stitch Control Stretch Stitch Control Pressure Regulator Sewing Light Seam Guides Presser Foot Lever Accessories Needles Needle, Thread and Fabric

Now that you are familiar with the controls on your machine and with the accessories provided for the machine, you are ready to start to sew with your new Kenmore sewing machine. Below are some good habits to follow each time you sit down to sew: , Test the needle -it should be straight, properly set and sharp on the point, It should be the correct size for the fabric and thread being used. Do not be afraid to change your needle frequently. Many of the new fabrics made of synthetic blends tend t

Raise the needle to its highest position by turning the handwheet counterclockwise, toward you, and lowering the presser foot. Loosen the needle clamp screw _ by turning it counterclockwise. Remove the needle from the needle clamp _. Insert a new needle into the needle clamp _ with the fiat side (_ to the rear. When inserting the needle into the needle clamp _, push it up as far as it goes. Tighten the needle clamp screw _ firmly by turning it clockwise. To check for a good needle, place the fia

Lift out the bobbin _ from the bobbin holder. J • Horizontal spool pin Spool pin Large spool holder Small spool holder \ \ \ Lift up the spool pin _. Place a spool of thread on the spool pin with the thread coming off the spool as shown. Attach the large spool holder _, and press it firmly J against the spool of thread. The small spool holder _ is used with narrow or small spools of thread. J • Additional spool pin Additional spool pin Spool pin hole Spool pin felt Spool stand The additional spo

31 Selector de patr6n ............................................................. 33 Control de puntada reversa ............................................... 33 SECCION III. COSTURA DE PUNTADA RECTA Puntada recta ................................................................. 35 • Para empezar a coser .................................................. 35 • Para terminar a coser .................................................. 35 Uso de las guias de costura ...............................

Warranty service is available by returning the sewing machine to the nearest Sears Service Center in the United States. IF THIS MACHINE IS USED FOR COMMERCIAL OR RENTAL PURPOSES, THE ABOVE WARRANTY COVERAGES APPLY FOR ONLY 90 DAYS FROM THE DATE OF PURCHASE This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. :::::::::::::::::::::::: :Sears ] :R.o:eb:u:c:k and Co_,:D/817 WA, H .o.ff:man: Estates:, :::::::::::::::::::::::::::::::::: GARA

SECTION 3. LEARN THE STITCHES = Use the Darning Plate Sometimes when you sew, you want to contro the fabric youself. The Darning Plate covers the feed dogs so that they do not touch the fabric. To Put on the Darning Plate: NOTE: The rectangular holes in the Darning Plate match the holes in the needle plate. In the darning plate, these holes are slightly to the left of center. 1. Position the darning plate with the 3 pins on the bottom. 2. Fit the darning plate pins into the needle plate holes. T

, KNOWING YOUR SEWING MACHINE Identifying Parts ................................................. 2, 3 Installing Machine ............................................... 4, 5 Converting to Free-arm Sewing ................................ 6 Winding the Bobbin ............................................... 7 Threading the Bobbin Case ...................................... 8 Threading of Top Thread ........................................ 9 USING THE CONTROLS Adjusting Top Tension ................