Votes - 3, Average rating: 3 ( )

Manafacture: Euro-Pro File size: 4.45 mb File name: 377-374-373-372-372H_ENG_REV_0504B.pdf Language of manual:

S.S. ) DECORATIVE EDGING Turn the ra w edgeunder 2cm a nd press. P lace the fabric rightsideup with the middle of the turnover under the center of the presser foot, so thatthe stitch s ews on to the fold a nd just aver the ta,w ed^e underneath. iW^IvWM SEWING BUTTONHOLES The built -in buttonhole mechanism of this machine makes it possible to sew button holes in a short time without turning the material. .................................................. Model 377/374 Model 373/372/372H Piessei foot buttonhole foot buttonhole foot Pattem selector B->• m-*• a -*• m a t H t B t H Stitch length dial 0.5 to 1 — Raise the foot and the needle to its highest position. Replace the foot with the transparent buttonhole foot for sewing buttonholes. Mark the location and the desired length of buttonhole on the fabric using a pencil or tailors chalk. Note: (Model EP 377 and 374 only) *To find the most suitable stitch length, it is better to s ew a s a mple buttonhole on a piece of wa s te fa bric. * When sewing very fine fabrics and synthetics, decrease the pressure of foot and sew over a piece of paper to prevent yarn distortion. * The mark on the stitch length dial shows a range of buttonhole sewing. An adjustment can be made by setting the mark, as s hown. * Buttonhole stitch length is adjustable only on one side. buttonhole foot coarse dense stitches stitches for heavy for light fabrics fabrics Q o range of stitch length 14 SEWING BUTTONHOLES (Model 377 and 374) 1. Set the pattern selector at d . Then pass the needle thread throughthe opening in the buttonhole foot and draw both needle and bobbin threads to the left side. Turn the balance wheel towards you until the needle comes to the point(i). 2.Lower the foot and sew slowly until the desired length is sewn, then stop the machine at (2). 3. Raise the needle and set the selector at D . Then sew several stitches of bar tack until the needle is at point (3). 4. Raise the needle and set the selector at [] then sewthe right side of buttonhole the same length as the left side of buttonhole. Stop the machine at (4). 5. Raise needle and set the selector at n then sew several stitches of final bar tack. Stop tie machine with the needle at point (5 ) . To lock theads, set the pattern selector at B§ (zero point of zigzag width). And sew a few stitches. 6. Cut thebuttonhole open carefully using a seam ripper, taking care not to damage the bar tacks. (Model EP 377 and 374 only) SEWING BUTTONHOLES (Model 373/372/372H) 1. Set the pattern selector at I I I III Then pass the needle thread through the opening in the buttonhole foot and draw both of needle and bobbin threads to the right side. Turn the balance wheel towards you until the needle comes to the point ( 1 ). 2. Lower the foot and sew slowly until a desired length is sewn, then stop the machine at (2). 3. Raise the needle and set the selector at H then sew several stitches of bar tack mtil the needle is at point (3). 4. Raise the needle and set the selector at E then sew the left side of buttonhole just as the same length as the right side of buttonhole. Stop the machine at (4). 5. Raise the needle and set the selector at Q then sew several stitches of final bar tack. Stop the machine with the needle at point (5). 6. Cut the buttonhole open carefully using a seam ripper, taking care not to damage the bar tacks. Note: To make a heavier buttonhole, sew twice by repeating the same procedure. (Model 373/3 72/3 72H) SEWING ZIPPERS ..............—................... Model 377 Model 374 Model 373/372/372H Presser foot zipper foot zi pper foot zipper foot Pattern selector M( ) A( cjlD ) 1-3( j ) Stitch length dial 1 to 4 1 to 4 — Raise the foot and the needle to its highest position by turning the balance wheel towards you. Replace the foot with the zipper foot. 1. Pin or baste the zipper tape to the fabric and place the workpiece in position under the foot. Attach snap on zipper foot so that the needle passes on its left ha nd side. * When starting sewing, both needle and bobbin threads ends should be put away under the foot. 2. Sew on the right side of the zipper by guiding Zipper teeth as close as possible to the needle drop. Before the foot reaches the slider on the zipper tape, raise the foot and open the zipper by keeping the needle in the fabric. Lower the foot and sew on the remaining of the seam, 3. To sew the left side zipper change position of foot to bring the foot to the left side of the needle. Sew on in the same way as you did on the right side of zipper. Element 15 E nglish HEMMING (Model 377 only) Presser foot ............. Pattern selector. S titch length dia l Raise the foot and the needle to its highest position. Replace the foot with the hemmer foot. Fold over the fabric edge by about 3mm (1/8 inches ) and place it under the foot. Secure the folded edge with a few stitches. Take out the workpiece and draw the hem into the hemmer foot by pulling o...

Download now

Please, enter two numbers from picture: