Votes - 4, Average rating: 4.3 ( )

Manafacture: White File size: 650.87 kb File name: 1086_white-1515,1525-x.pdf Language of manual:

Thread. Needle table Sewing (pattern selector) and operation table 16 To start sewing 17 To finish seam 18 19 Straight stitch 19 Zigzag sewing Overcasting Stretch stitch 20 Blind stitch 21 & 22 23 Button sewing 23 Binding Zippersewing 24 Button hole sewing Hemming 26 Twin Needle 27 27 Embroidery 28 Quilter 28 Seam guide 29 Maintenance (Cle.3ning and oiling) Checking Performance Problems WHAT TO DO NAME OF PARTS (FRONT VIEW) Pattern selector dial 7 Spool pins Take up lever 8 Top cover Thread tension dial 9 Stitch length dial Presser foot 10 Reverse button Shuttle cover 11 Thread guide for upper threading Extension table (REAR VIEW) Bobbin winder spindle Bobbin winder Stop Face cover plate eedle clamp screw Presser foot lever —2— REMOVING EXTENSION TABLE of table and pull out in direction of arrow. 1. Hold the left end FREEARM SEWING 1. Especially useful when sewing sleeves, pants leg, tubular fabrics etc more easily. 2. To sew tubular just slip the sleeve or pants leg on the free arm as shown above. 3. This sewing machine can be used as a flat bed machine, but easily converts to free arm machine by removing the extension table. _ WINDING THE BOBBIN = ::m1ff 1. Release stop motion knob. 2. Thread as shown. 3. When bobbin is filled, tighten stop motion knob. Push bobbin winder spindle in direction of arrow. When bobbin winding is com pleted return sindIe to original position. When bobbin winding is in correct, release the screw of upper thread guide and ad just up or down until bobbin winding is balanced. —6— REMOVING BOBBIN CASE AND BOBBIN Hinged latch I - Raise needle to its highest 2. Open hinged latch of position and open the bobbin case and pull bob shuttle race cover. bin case out of machine. th htf’h k,-k bin will fall out easily. INSERTING BOBBIN INTO BOBBIN CASE 1. Pull off 5cm of thread 2. Guide the end of thread from bobbin and insert it into slot. into bobbin case as shown. J J Tension spring 3. Pull Into slot and under 10cm tension spring and draw out about 10 cm of thread. —7— INSERTING BOBBIN CASE INTO SHUTTLE RACE 7, 1. Raise needle to its highest position, pulling thread to the front, open the latch of bobbin case and hold it. nsert 2. Holding latch open, place bobbin case onto centre pin in shuttle and release latch —8— DRAWING UP BOBBIN THREAD 1 Hold upper thread with left hand, turn the hand wheel slowly towards you until the needle goes down and comes up. Then stop the hand wheel when the takeup lever is at its highest position. Lightly draw up the upper thread will be brought up in a loop. 2. Pull out both threads and presser foot machine. to the rear of CHANGING SEWING DIRECTIONS 1. Lower needle down into fabric and 2. Put down presser foot and raise presser foot, pivot the fabric start to sew. around the needle to change direction as desired. —10— MACHINE LEVELING DOWN up —11— ADJUSTING THREAD TENSION Correct Fabric Upper thread Weak Strong Bobbin thread Upper thread tension may be adjusted by turning the thread tension dial. . Inside of fabric Upper thread Lower thread tension can be adjusted by turning screw on bobbin case slightly to the right (clock-wise) to increase tension. (Anti-clockwise) to the left to decrease tension. —12— REGULATING THE PRESSER FOOT PRESSURE set lever at 1, set at lever for desired pressure, for tight fabrics 1. Push down ind3Iorheavy fabrics 2 for mediumfjb1 poor feeding, skipped stitches, or- -difficult...

Download now

Please, enter two numbers from picture: