Login:
Votes - 2, Average rating: 3.5 ( )

User manual Bernina, model 1000

Manafacture: Bernina
File size: 1.02 mb
File name: 955_ww-1000-x.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


. Cleaning of race .and shuttle hook. 26 Cleaning and oiling 27 Trouble shooting guide 28 a NAME OF PARTS (FRONT SIDE) 6 1 Pattern selector dial 2 Take up lever 3 Tread tension dial 4 Tread guide for upper threading 5 Presser foot 6 Shuttle cover 7 Extension table 8 Spool pin 9 Top cover 10 Stitch length dial 11 Reverse button 12 Bobbin winder spindle 13 Bobbin winder stopper 14 Stop motion knob 15 Hand wheel 16 Handle 17 Upper thread guide 18 Face cover 19 Thumbscrew 20 Needle plate 21 Needle clamp screw ACCESSORI ES Bobbin Felt Zigzag foot Button hole foot (On machine) Button foot Machine Oil Zipper foot Button hole cutter Screw driver Needle #11 #14 7 REMOViNG EXTENSION TABLE To convert the machine from flat-bed use to free-arm use simply remove the ex tension table as shown. THIS IS ONLY APPLICABLE TO MACHINES MANUFACTURED FOR THE UNITED KINGDOM IMPORT ANT The wires in this mains lead are coloured in accordance with the following code: BLUE NEUTRAL — — BROWN LIVE NOTE. A the colours of the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect BROWN wire to terminal marked L or coloured RED. Connect BLUE wire to terminal marked N or coloured BLACK. FIT CORRECT PLUG TO POWER CORD WHEN USING A B.S. 1363 FUSED PLUG. A 3 AMP. FUSE MUST BE FITTED. If the terminals of the plug are unmarked consult a qualified electrician before use. tM,en leaving the sewing machine unattended, the plug must be removed from the socket outlet ‘Mien servicing the sewing machine, or when removing covers or changing lamps, the machine or the electrical set must be disconnected from the Supply by removing the plug from the socket outlet. THE MAXIMUM INPUT OF LAMP: 240 V 15 W. THIS APPLIANCE CONFORMS TO THE STATUTORY RADIO INTERFERENCE SUPPRESSION REGULATIONS. 8 AND SEAM Raise the presser foot. Pull the one-touch lever towards you and the will be Raise the presser bar and fit shank as released. Centre new foot under shank. shown. (1) Insert quilting/seam guide carefully so as Lower shank until groove is directly not to damage the holding spring. (2) above and touching the pin. Pull one- touch lever towards you and the foot will become engaged. (3, 4) Shank set strew Ti9hj Loosen Shank 4 WINDING THE BOBBIN 1. Release stop motion knob. 2. Thread as shown. 3. Place bobbin onto spindle and hand-wind thread onto bobbin in an anti-clockwise direction for 5 or 6 turns. (When bobbin is filled re-tighten stop motion knob) Bobbin 4. Push bobbin winder spindle against stopper, in direction of arrow, and depress foot pedal. 5. When bobbin winding is com pleted return spindle to its original position. Note: If the bobbin winding should be uneven (it is factory set) the thread guide can be raised or lowered to achieve the correct winding. Remove the top cover and adjust with a suitable tool. 11 REMOVING BOBBIN CASE AND BOBBIN Hinged 1. Raise needle to its highest 2. Open hinged latch of position and open the bobbin case and pull bob- shuttle race cover, bin case out of machine. 3. Release the latch and bob bin will fall out easily. INSERTING BOBBiN INTO BOBBIN CASE SLOT 1. Pull off 5cm of thread Guide the end of thread 2. from bobbin and insert it into slot. into bobbin case as shown. Tension spring 3. Pull into slot and under tension spring and draw out about 10 cm of thread. 12 7 INSERTING BOBBIN CASE INTO SHUTTLE RACE nse If Hinged latch —I 1. Ensure needle is at its highest position. 2. Holding latch open, piace bobbin case onto centre pin in shuttle and release Pulling thread to the front, open the latch of bobbin case and hold it. latch. CHANGING NEEDLE 1. Raise needle to its highest position. 2. Loosen needle clamp screw and re move old needle. 3. With the flat side of the needle facing away from you, insert needle as far up as it will go. 4. Tighten the needle clamp screw securely. Note: At the first sign of any stitching irregularity always change the needle for a new good quality one. 13 1 ( DRAWING UP BOBBIN THREAD Hoid the top thread with a slight tension ri your left hand and rotate the handwheel towards you so that the needle goes down and up again, then gently pull your thread out towards the rear and under your sewing foot and you are readyto start sewing. I 4 CHANGING SEWING DIRECTIONS 1. Lower needle down into fabric and 2. Put down presser foot and raise presser foot, pivot the fabric start to sew. around the needle to change direction as desired. 15 REGULATING THE PRESSER FOOT PRESSURE / —7——r€ QJJ2or ‘B N - To release the pressure, push ring (A) downwards. This causes the regulator to spring up to its highest position. The material is now free from any pressure of the presser foot. For sewng thin or light materials, push regulator (B) down just a little to provide the light pressure required. If you are sewing thick or heavy materials, push the regulator (B) farther down to increase the pressure on the material. DROP FEED !‘ Lower feed dog...

Other models in this manual:
Sewing Machines - 1000 (1.02 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category