• Frequently clean grinding dust from beneath grinder. • Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the wheel. • Always wear eye protection and check that the eye shields on the grinder are properly adjusted. • Always turn the grinder off when it is not in use and never leave it unattended without first switching off and removing the power plug. Never leave the grinder until the grinding wheels have come to a complete stop. • Mak
• Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris INSTRUCTION MANUAL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A Contents Contents Warranty 2 Introduction 3 Environmental protection 3 Descr
Holding and guiding the tool 1. Always clamp the work piece. 2. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure. The weight of the tool alone provides sufficient pressure. 3. Cutting discs become very hot when in use. Take care not to touch them until they have cooled down. 4. Hold the tool securely and make sure that you have full control at all times. 5. During a cutting operation, maintain an angle of 30 to 40 degrees between the to
Warranty 2 Introduction 3 Environmental protection 3 Description of symbols 3 Specifications 3 Safety instructions 4 Additional safety rules for sanders 5 Unpacking 6 Contents of carton 6 Assembly 6 Know your product 7 Switching on and off 8 Attaching a sanding sheet 8 Selecting the right grade of sanding belt 8 Sanding 9 Dust extraction 10 General inspection 10 Cleaning 10 Description of symbols The rating plate on your tool may show symbols. These represent important information about the prod
The correct power tool will do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d. Store idle power tools out
11/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL 1/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL ContentsContents Introduction 3 Description of symbols 3 Specifications 3 General safety rules 4 Additional safety rules for belt & disc sanders 5 Unpacking 6 Accessories 7 Know your product 8 Getting to know your belt and disc sander 9 Mounting belt and disc sander to workbench 9 Installing sanding disc and guard 9 Installing work support 9 Installing table assembly 10 Auxiliary mounting for ver
Use of the power tool for operations different from intended could result in a hazardous situation. Service • Have your power tool serviced by a qualified repair personnel using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Additional safety rules for angle grinders • Fully unwind cable drum extensions to avoid potential overheating. • When an extension cable is required, you must ensure that it has the right ampere rating for your power tool
• When sanding wood, always connect the dust extraction filter. • Take special care to guard against harmful and toxic dusts when sanding lead-based painted surfaces, woods and metals, including the following: - All persons entering the work area must wear a mask specially designed for protection against toxic dust and fumes such as those arising from the sanding of lead paint . - Children and pregnant women must not enter the work area. - Do not eat, drink or smoke in the work area. • Before us
Main handle 3. Dust extraction canister 4. Hook & loop base 5. Paper clamp 6. Variable speed control 7. Front handle 8. Handle lock 9. Hole punch 10. Dust extraction adaptor 11. Sandpaper (2 x 80G) 1 6 2 7 8 3 5 4 10 9 11 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result