Votes - 3, Average rating: 4.3 ( )

Manafacture: Milwaukee File size: 283.09 kb File name: Language of manual:

The use of extension cords of inadequate size wire causes a serious drop in voltage, loss of power and possible motor damage. This table is based on limiting line voltage drop to 5 volts at 150% of rated amperes. Ampere rating 0- 2.10- 3.5- 5.10- 7.10- 12.1- 16.1- (on Nameplate) 2.00 3.4 5.00 7.0 12.0 16.0 20.0 Ext. Cable Length Wire Size 25 Ft. 18 18 18 18 16 14 12 50 Ft. 18 18 18 16 14 12 10 75 Ft. 18 18 16 14 12 10 8 100 Ft. 18 16 14 12 10 8 8 150 Ft. 200 Ft. 16 16 14 14 12 12 12 10 8 8 8 6 6 4 available as flexible 300 Ft. 14 12 1P 6 6 4 4 400 Ft. 12 10 Ö 6 4 4 2 500 Ft. 12 10 8 6 4 2 2 600 Ft. 10 8 6 4 2 2 1 800 Ft. 10 8 6 4 2 1 0 1000 Ft. 8 6 4 2 1 0 0 IF USING AN EXTENSION CORD OUTDOORS, BE SURE IT IS MARKED WITH THE SUFFIX "W-A" ("W" IN CANADA) TO INDICATE THAT IT IS ACCEPTABLE FOR OUTDOOR USE. Read All Instructions And Save Them For Future Reference MILWAUKEE ORBITAL SANDERS CAUTION: ALWAYS TURN SWITCH OFF AND UNPLUG TOOL BEFORE ATTACHING OR REMOVING SANDPAPER OR DUST PICK-UP. SANDPAPER The sandpaper recommended for power sanding is an aluminum-oxide, open coat paper. This type of paper is recommended since it will not clog as easily as closed coat papers and will wear longer. It can be used for sanding all metals, hard and medium woods, plastics and similar materials. A garnet type sandpaper is acceptable for use with the MILWAUKEE Orbital Sander but the life of this paper is extremely short. Flint type papers are not recommended. ATTACHING SANDPAPER The sandpaper size for the No. 6012 MILWAUKEE Orbital Sander is 3-2/3" x 9" or one third of a standard 9" x 11" sheet of sandpaper. The No. 6014 Orbital Sander uses a 4-1/2" x 11" or one half of a standard 9" x 11" sheet of sandpaper. Score the back of the paper with a knife before attempting to break or tear the 9" x 11" sheet. The paper will tear neatly when the abrasive sides are folded together. To attach paper to a sanding pad, roll the ends of the sheet so that the last inch of each side curls up. Insert the curled end in the spring clamp and draw the paper tightly over the pad. Be sure the paper is centered. Insert the paper into the opposite spring clamp. Loose or poorly centered paper does a poor sanding job and causes excessive paper wear. OPERATION Turn the switch to the on position before applying the sander to the workpiece. This prevents rough action which results when starting under load. Use long slow strokes. For the first stage of finish sanding select a coarser grit paper if the workpiece is rough. Follow with finer grit paper until the desired finish is obtained. Apply only slight pressure when guiding the tool. Let the weight of the sander do the work. Excess sanding pressure can result in faster material removal but may cause scratches and other irregularities which are very difficult to remove with fine grit sandpaper. The MILWAUKEE Electric Tool Corporation assumes no responsibility for any damage or accidents resulting from the misuse of this tool, its misapplication or the nonadherence to precautionary safety measures. INSTALLATION INSTRUCTIONS DUST PICK-UP KIT CATALOG NO. 48-09-0300 For MILWAUKEE Orbital Sander Model 6014 CAUTION: ALWAYS TURN SWITCH OFF AND UNPLUG TOOL BEFORE ATTACHING OR REMOVING SANDPAPER OR DUST PICK-UP. DUST BAG Before attaching the dus...

Download now

Please, enter two numbers from picture: