Votes - 3, Average rating: 4.3 ( )

Manafacture: Black & Decker File size: 261.27 kb File name: Language of manual:

13. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. Charging the Battery Pack THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS. The charger is designed to use standard household 120 volt 60 Hz power. 1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC 2. Slide the charger onto the battery pack as shown in Figure A and let the battery charge initially for 9 hours. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 6 hours. A B 3. Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. NOTE: To remove the battery from the tool, press down on the release button on the back of the battery (Figure B) and slide out. Important Charging Notes 1. After normal usage, your battery pack should be fully charged in 3 to 6 hours. If the battery pack is run-down completely, it may take up to 6 hours to become fully charged. Your battery pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours. 2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above 105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F.(24°C). 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the battery pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C) (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the battery pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its battery pack in a depleted condition. 6. To prolong battery pack life, avoid leaving the battery pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery pack life. 7. The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. SAVE THESE INSTRUCTIONS Assembly CAUTION: Before assembly, always ensure that the battery is removed from the tool. Overview (Fig.1) 1. On/Off Switch 2. Battery Pack 3. Random Orbit Sanding Base 4. Large Detail Sanding Base 5. Finger Attachment Sanding Base Random orbit sanding base With this sanding base, you can use the tool as a random orbit sander. Fitting and removing the sanding base (Fig. 2) • Place the sanding base (3) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding discs • Hold the tool with the sanding base facing upwards. • Place the sanding disc onto the sanding base (3). The holes in the disc do not need to line up with the holes in the base. Large detail sanding base With this sanding base, you can use the tool as a detail sander or an orbital sander. Fitting and removing the sanding base (Fig. 3) • Place the sanding base (10) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding sheets (Fig. 4) • Detach the two diamond-shaped tips (11) from the sanding sheet (12). • Hold the tool with the sanding base facing upwards. • Place the sanding sheet (12) onto the sandin...

Download now

Please, enter two numbers from picture: