Votes - 4, Average rating: 2.8
(
)
)
|
manual abstract
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: Clarke® , 2100 Highway 265, Springdale, Arkansas 72764 EZ-8 Sander READ THIS BOOK LEA ESTE MANUAL LISEZ CE MANUEL Operator's Manual Manual del operador Manuel de l’utilisateur English (2 - 13) Espanol (14 - 25) Francais (26 - 37) ES EN FR ENGLISH EN Contents of this Book Operator Safety Instructions .........................................................3 Introduction and Machine Specifications.......................................5 How to Transport the Machine ......................................................6 Machine Set-Up ...........................................................................7 How to Operate the Machine ........................................................9 Sanding Cuts and Sandpaper .................................................. 10 Sander Adjustment Procedures..................................................11 Routine Maintenance..................................................................12 Troubleshooting .........................................................................13 Section II Parts and Service Manual Assembly Drawing #1 ................................................................40 Assembly Parts List #1 ..............................................................41 Assembly Drawing #2 ................................................................42 Assembly Parts List #2 ..............................................................43 Wiring Diagram..........................................................................44 -2-Clarke® American Sanders Operator's Manual (EN) - EZ-8 Sander ENEN ENGLISH OPERATOR SAFETY INSTRUCTIONS DANGERmeans: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Operator's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Operator's Manual and on your machine. WARNING means: Injury can occur to you or to other personnel if the WARNING statements found on your machine or in this Operator's Manual are ignored or are not adhered to. Read and observe all WARNING statements found in this Operator's Manual and on your machine. CAUTION means: Damage can occur to the machine or to other property if the CAUTION statements found on your machine or in this Operator's Manual are ignored or are not adhered to. Read and observe all CAUTION statements found in this Operator's Manual and on your machine. DANGER: Failure to read the Operator's Manual before operating or servicing this sanding equipment could result in injury to the operator or to bystanders and could cause damage to the equipment. Read and observe all safety statements found in this manual and on the sanding equipment. Make sure all labels, decals, warnings, cautions and instructions are fastened to the equipment. Replace any that are damaged or missing. You must have training in the operation of this equipment before using it. If the operator is unable to read this manual, have it explained fully before they attempt to use this equipment. Sanding/finishing wood floors can create an environment that can be explosive. The following safety procedures must be adhered to: • Cigarette lighters, pilot lights and any other source of ignition can create an explosion when active during a sanding session. All sources of ignition should be extinguished or removed entirely if possible from the work area. • Work areas that are poorly ventilated can create an explosive environment when certain combustible materials are in the atmosphere, i.e., solvents, thinners, alcohol, fuels, certain finishes, wood dust and other combustible materials. Floor sanding equipment can cause flammable material and vapors to burn. Read the manufacturer's label on all chemicals used to determine combustibility. Keep the work area well ventilated. • Spontaneous combustion or an explosion can occur when working with sanding dust. The sanding dust can self-ignite and cause injury or damage. Sanding dust should be disposed of properly. Always empty the sanding dust into a metal container that is located outside of any building(s). • Remove the contents of the dust bag when the bag is 1/3 full. Remove the contents of the dust bag each time you finish using the equipment. Never leave a dust bag unattended with sanding dust in it. • Do not empty ...