Votes - 3, Average rating: 3
(
)
)
|
manual abstract
A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS. How to use Switch action To start the tool, simply pull the trigger. Release the trigger to stop. For continuous operation without having to keep your finger on the trigger, just pull the trigger and then push in the lock button with your thumb. To stop the tool from lock posi- tion, just pull the trigger again and release it. Mounting belt With the tool unplugged and the lever pulled out all the way, slip the belt over the rollers with the arrow direction on the belt the same as that of tool revolution (or belt life is shortened). Belt adjustment Flip sander over on its back and use the adjustment knob to obtain equal tension of belt over the front and back rollers. Then plug in sander and switch it on, using the adjustment knob to center the belt as it runs over the rollers. Failure to adjust belt porperly over rollers can result in frayed belt edges. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. Brush holder cap To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESS0RIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Abrasive belts 0 Belt type and use AA -For wood, iron and steel. CC -For stone and plastics. Grit Pari No Use Sheets per pack AA40 742306-7 Coarse AA60 742307-5 742314.8 Coarse AA80 742308-3 74231 5-6 AAlOO 742309-1 Medium 10 CClOO 742316-4 Medium AA120 742310-6 AA150 742311-4 AA180 742350-4 Fine 71 71 CC120 742317-2 CC150 I 742318-0 1 Fine I AA240 742312-2 747319-R Carbon plate Steel plate Part No. 423027-7 Part No. 342466-1 CAUTION : Install the steel plate so that THE EDGE OF THE STEEL PLATE WILL NOT PROTRUDE FROM THE EDGE OF THE BASE PLATE ON THE SIDE WITH THE BELT INSTALLING LEVER. IF THE PLATE IS ALLOWED TO PROTRUDE, IT MAY CAUSE INJURY. Dust bag Part No. 122296-4 76mm(3") BELT SANDER Model 9900B 1: M_AC-HS MACHINE ~ P H Screw M4x30 (With Warheil 38 1 Shoe 21 v Pulley 5-25L 39 2 Rivet 0-5 113 ' Motor Housing 40 1 Name Plate q1 (With Brush Holder x 2 & S Screw M5x8 x 21 41 1 Edge Slider 412 Carbon Brush 42 1 Retaining Ring S-12 52 Brush Holder Cap 43 1 Cup Washer 12 6 1 FIELD ASSEMBLY (With Garter Spring x 21 44 Tension Roller 45 1 Cup Washer 12 1 BafflePlate 46 ~ 1 Tension Roller Shafr 811 Ball Bearing 6200LCB 47 2 P H. Screw M4x10 (With Warherl 91 Insulation Washer 48 1 Safety cover 49 1 SupFart Pm 10 2 H Bolt M5x45 (With Warherl 11 1 Dust Bag ~ M 1 Tenrion Roller Arm 12 ARMATURE ASSEMBLY 1 IArrembled Items 8.9. 12. 13.3 141 51 1 Compreirion Spring 11 I 13 1 Fan 75 52 1 Driving Roller 14 I Ball Bearing 6xK)LLB 53 6 C H. Screw M5x18 15 1 Dust Collecror Bracket 54 1 Key 4 P H Screw M5x25 (With Warherl 55 1 Cup Washer 12 17 ~ 1 1 Rubber Pin 4 56 1 Frame (With Rivet x 2. Dust Guide, 18 2 P H Screw M4x18 IWith Washer) 16 4 Plane Bearing 12 x 2 & Swnge Shed ~ 57 1 P H. Screw M5x12 (With Washer1 19 1 Dust Collector Cover 58 1 Needle Bearing 810 201 separator 53 1 Helical Gear 10 21 1 Rubber Pin 4 MI 1 Rubber Pin 4 P H Screw M5x12 (With Washer) 61 1 Ball Bearing 6200LLB 22 1 ~ 23 1 Fan 74 62 1 Gear Cover 24 1 Handle Cover 63 1 V-Pulley 5-45 261 Switch 64 2 P H Screw M4x18 (With Warherl 27 2 P. H Screw M4x18 (With Washer) ~ 65 1 Retaining Ring S-12 28 1 Strain Relief 66 A.R. T Washer 12 29 1 Cord Guard 67 1 Helical Gear 48 CORD ASSEMBLY (Assembled Cord, Plug & Cord Guard1 68 1 Bale Plate P H Screw M5x40 (With Warher) 69 1 Cork Rubber Plate 32 I 1 Belt cover 70 2 P H Screw M4x10 (With Washer) 33 1 Poly V-Belt 5-304 71 1 Steel Plate ~ Sleeve 6 72 2 P H. Screw M4x10 (With Warherl 4 1 ACCESSORY 401 1 Abrasive Belt 533-100 i 1 MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during th...