Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
For future reference, please complete the owner’s record below: Model_____________ Serial No.____________ Purchase Date_____________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Tool Name: Stand, Bench Grinder Pedestal Item Number: 42986 Stand Height: 29-1/2” Table Dimensions: 11” x 9-5/8” Table Mount Slots: (Qty =6) 5/8” wide Base Dimensions: 17-1/4” Triangle Base Mount Holes: 3/8” Diameter Material: Cold Rolled Steel and Cast Iron Finish: Grey Enamel Paint Weight: 21.60 Maximum Weight Capacity: 75 Lbs. Warning: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO THIS PRODUCT, BUT MUST BE SUPPLIED BY THE OPERATOR. The Operator PLEASE REMEMBER: Do not operate the product to be used with this item, if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment/reflexes might be impaired. Do not wear loose clothing or jewelry as they can be caught in parts. Protective gloves and non-skid footwear are recommended. Wear restrictive hair covering to contain long hair. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Maintain proper footing and balance at all times. Use the right product for the job. Do not attempt to force a large tool or attachment to do the work of a smaller industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. Work Area TO AVOID RISK OF PERSONAL INJURY, EQUIPMENT DAMAGE, FIRE AND SHOCK, MAKE SURE YOUR WORK AREA IS: Free of damp, wet or rainy conditions. Free of children (never let them handle tools or machinery). Well-lit. Clean and uncluttered. Before Using Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Make sure all Nuts and Bolts are tight. Use only Bench Grinders that are fully compatible with the Bench Grinder Pedestal Stand. The Bench Grinder Pedestal Stand fits most Harbor Freight Tool Bench Grinders, but you should always check for sure before using. Use of the Pedestal Stand is for use with bench grinders only. Assembly Your Pedestal Stand will require assembly prior to use. It is important that you read the entire manual to become familiar with the unit BEFORE you set up the Stand. Before assembling your Stand, be sure that you have all parts described in the Parts List and Parts Diagram on the last pages of this manual. Set out all parts on a clear work surface prior to assembly. Warning: Use only bench grinders that are fully compatible with the Bench Grinder Pedestal Stand. Using bench grinders which do not fit this stand may result in harm or serious injury to the operator. The Bench Grinder Pedestal Stand fits most Harbor Freight Tool Bench Grinders, but you should always check for sure before using. Use the Pedestal Stand for bench grinders only. Step 1) Mount the Base (3) to a heavy-duty block of wood which is larger than the Pedestal Stand Base, or into cement for safety and stability. A rubber mat should be placed between the Base (#3) and the mounting surface to reduce vibration. The Mounting Holes on the Base (3) are 3/8” in diameter. Insert appropriate screws (not included) through the Base (3) and into a flat and secure surface. The mounting surface must be able to support the weight of the Stand as well as the Grinder and work pieces during use. Step 2) Insert the Column (#2) into the hole in the Base (3). Insert a Bolt (4) into each hole in the Base (3) and tighten them firmly against the Column (2). Step 3) Slide the Work Table (1) into place on top of the Column (2). Thread one Bolt (4) through each hole in the WorkTable. Tighten the Bolts (4) until they are firmly against the Column. Step 4) Make certain that all Bolts (4) are tightly in place and that the Stand is secure. Step 5) Secure the bench grinder to the Work Table (#1) with six appropriate size bolts, washers and nuts (not included). Step 6) Make sure that the Pedestal Stand and the bench grinder are secure before using. Unpacking UNPACK AND CHECK CONTENTS When unpacking your Bench Grinder Pedestal Stand, check to make sure the following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. PartDescriptionQuantity1Work Table12Column13Base14Bolt M8 x 244 Note: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY...