Votes - 5, Average rating: 3.4
(
)
)
|
manual abstract
For technical questions please call 1-800-444-3353 SPECIFICATIONS ITEM DESCRIPTION Body Construction Body: Formed and Stamped Sheet Steel Finish Black Powder Coat Overall Dimensions 34-1/4”H X 15-3/4”L X 12-3/8”W Top Mounting Holes 3/8”W X 2-3/4”L (6X Slotted Holes) Base Mounting Holes 308” Dia. (4X) Lower Shelf 13-3.8” X 12-3/8” Middle Shelf 12-1/8” X 12-3/8” Top Shelf 10-5/8” X 12-3/8” Top Dimensions 12-7/8”W X 10”L X 1-7/8”H Overall Weight 47 Lbs. SAVE THIS MANUAL You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. SAFETY WARNINGS AND PRECAUTIONS 1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. 2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children to climb on this product or play around tools or supplies. 3. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. 4. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use a Buffer or Grinder mounted on this product when you are tired or distracted. 5. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 6. DO NOT MODIFY THIS PRODUCT. This product is designed to support a Grinder or Buffer. Do not modify this Cabinet in an attempt to use it for other purposes. 7. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 8. USE THIS PRODUCT only for its intended use, as described in this manual. Do not use attachments or modify it in any way. 9. BE SURE to use proper hardware (not included) to secure Grinder or Buffer. NOTE: Always read and adhere to all warnings and instructions provided in the instruction manual of the buffer or grinder being used. WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SKU 40089 PAGE 2 UNPACKING When unpacking, check to make sure all parts shown on the Parts List (page 4) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS NOTE: All parts below refer to the parts listed on page 4 of this manual. Assembly 1. To assemble Steel Grinding/Buffing Cabinet with three storage shelves you must first lay out all parts and hardware on a clean surface. 2. Identify the Top Shelf (#6), the two Side Panels (#2A, #2B, right and left), the Base (#1), and the Back Panel (#5). #2B #2A #1 #5 #9, #8, #7 3. Starting with the Base (#1), fit the side panels over the Base, lining up the holes. Use the Bolt (#9) through the holes. Secure with Washer (#8) and Nut (#7). Repeat with Side Panels (#2A & #2B). Attach Back Panel (#5) to Side Panels and Base in the same way. 4. Slide in Shelves (larger on bottom and graduating up to smallest) (C & D). Secure each shelf with Bolts (#9), Washers (#8) and Nuts (#7) to Side Panels and Back Panel. #D #6 #C 5. Attach Top (#6) aligning with remaining holes. With Bolt (#9) through the holes, secure with Washer (#8) and Nut (#7) through front and back of Cabinet. 6. Choose where you want to place Cabinet permanently. Anchor through holes in Base (#1) with hardware for cement or wood flooring, depending on where you choose to mount Cabinet so it is secure during Grinding or Buffing for a strong sturdy work surface. (Hardware not included.) 7. Attach your Buffer or Grinder through the 6 top mounting holes (3/8” H X 2-3/4” L). Hardware will be required (not supplied). A non flammable rubber pad (not supplied) for insulation, is recommended between the Cabinet Top and the Buffer or Grinder. This pad will help reduce vibration. SKU 40089 PAGE 3 PART # PART # QTY 1 Base 1 2A Left Side 1 2B Right Side 1 C (larger) Shelf 1 D (smaller) Shelf 1 5 Back Panel 1 6 Top (with sloted holes) 1 7 Nut (10MM) 16 8 Washer 16 9 Bolt (M6 X 1,00MM Round Flat) 16 (#9) (#2A) (#6) (#2B)(#5) (D) (C) (#1) (#7) (#8) MAINTENANCE 1. For better and safer performance, keep all parts of this product clean and dry at all times. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS ...