Votes - , Average rating:
(
)
)
Manafacture: Grizzly
File size: 678.95 kb
File name: t10024_m.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Failure to do so could result in damage to the machine or personal injury. shipment, you should inventory the contents. Copyright © November, 2007 by grizzly iNdustrial, iNC. revised may, 2011 (Jb) WARNING: NO pORTION OF THIS MANUAL MAY bE REpRODUCED IN ANY SHApE OR FORM WITHOUT THE WRITTEN AppROvAL OF GRIzzLY INDUSTRIAL, INC. (For models maNuFaCtured siNCe 11/07) #Jb10089 priNted iN ChiNa Operations Stone Dresser the stone dresser is used to clean the grinding wheel when it is loaded with metal filings. it can also be used to adjust the grit of the wheel to approximately 220 or 1000. To use the stone dresser: 1. disCoNNeCt griNder From poWer! 2. place the universal support in the vertical mounts and position it approximately ." above the grinding wheel, then tighten both mounting knobs. 3. Connect the grinder to power and turn it ON. 4. Wearing gloves, carefully place the stone dresser against the universal support, then lower it onto the grinding wheel (Figure 3). —if you wish to change the grit of the wheel to approximately 1000 grit, then place the finer-grained surface against the wheel. —if you wish to clean the surface of the wheel or change the grit back to approximately 220 grit, then place the coarse-grained surface against the wheel. stone dresser Figure 3. stone dresser. 5. press the stone dresser against the grinding wheel until the desired results are achieved. turn the grinder OFF when complete. Universal Sharpening Jig 1. disCoNNeCt griNder From poWer! 2. place the universal support in either the vertical or horizontal mounts, depending on the desired grinding action as described in the model t10010/t10097 user manual. Note: Never place the universal support in the vertical mounts when using the stropping wheel. This will result in sharpening against the rotation direction and will cause damage to the leather wheel. 3. slide the universal sharpening jig onto the universal support and thread in the universal sharpening jig knobs as shown in Figure 4. universal sharpening Jig universal sharpening Jig Knob universal support Figure 4. universal sharpening jig. 4. adjust the grinding/sharpening angle by raising or lowering the universal support and tilting the universal sharpening jig as needed. 5. When the desired angle is achieved, tighten the four knobs, then connect the grinder to power and turn it ON. 6. place the workpiece onto the universal sharpening jig, as shown in Figure 4, then slide it onto the surface of the wheel. use a firm grip on the workpiece, but do not use heavy pressure against the wheel. be sure to move the workpiece back and forth across the surface of the wheel while grinding to prevent excessive wheel wear. -2 t10024 Wet grinder accessory Kit #2 the chisel sharpening jig is capable of accurately 3. Clamp the chisel (bevel-side down) into the sharpening a variety of chisels. the jig must be jig using the knob, as shown in Figure 7. assembled and used differently depending on the your exact clamping method may vary slightly tool you are sharpening and the way you want it depending on your chisel. to be sharpened. To assemble the jig for beveled chisels: 1. Completely disassemble the chisel sharpening jig as shown in Figure 5. Figure 5. Jig disassembled. 2. reassemble the jig and the jig holder as shown in Figure 6. Jig holder Chisel sharpening Jig Figure 6. beveled chisel jig assembled. To sharpen beveled chisels: 1. disCoNNeCt griNder From poWer! 2. place the universal support in either the vertical or horizontal mounts, depending on the desired grinding action as described in the model t10010/t10097 owner's manual. t10024 Wet grinder accessory Kit #2 Figure 7. Clamping bevel chisel (2-sided bevel). 4. place the assembled jig onto the universal support, as shown in Figure 8. Figure 8. grinding beveled chisels. 5. adjust the grinding angle by sliding the universal support in or out and by repositioning the chisel in the jig. once the desired angle is achieved, tilt the chisel away from the grinding wheel, then connect the grinder to power and turn it ON. 6. return the chisel onto the surface of the wheel. use a firm grip on the chisel, but do not use heavy pressure against the wheel. move the chisel back and forth across the surface of the wheel while grinding to prevent excessive or uneven wheel wear. -3 To assemble the jig for hollow chisels: 1. Completely disassemble the chisel sharpening jig as shown in Figure 5. 2. re-assemble the jig as shown in Figure 9. Chisel sharpening Jig Figure 9. hollow chisel jig assembly. To sharpen hollow chisels: 1. disCoNNeCt griNder From poWer! 2. place the universal support in either the vertical or horizontal mounts, depending on the desired grinding action as described in the model t10010/t10097 owner's manual. 3. Clamp the chisel (bevel-side down) into the jig, as shown in Figure 10. No single clamping method works best for all chisels and only trial-and-error with each specific tool will give the best clamping orientation. Tip: For ...