Votes - 3, Average rating: 4
(
)
)
|
manual abstract
It will have to be charged for 3 hours before use. DO NOT charge longer than this or damage to the battery may occur! To charge the battery: 1. Remove the battery from the mini grinder. 2. Insert the battery into the charger as shown in Figure 2. Figure2. Charging the battery. 3. Plug charger into power source and allow the battery to charge for 6 hours. The green light indicates the battery is charging. 4. Replace battery in mini grinder before operation. Installing Bits The Model H6156 uses bits and cutters with an 1.8" diameter shaft. See the Grizzly catalog or website for a complete listing of available bits and accessories. DO NOT use bits or cutters with a cutting surface larger than 1". The bit could break apart under the stresses of high speed use caus- ing serious personal injury. To install a bit: 1. Unplug the tool from the power source! 2. Depress the collet lock shown in Figure 3 and loosen the collet nut. The collet lock will engage during rotation, preventing further rotation of the collet nut. DO NOT completely remove the collet nut from the shaft. Collet Lock Figure3. Collet lock. -6- Model H6156 Cordless Mini Grinder 3. Insert the end of a bit into the collet. At least 1.2" of the bit shaft should be mounted into the end of the collet. 4. Rotate the collet nut while depressing the collet lock to secure the bit. Only tighten 1/3 of a turn with the collet wrench. Failure to wear safety glasses while operating the grinder could cause serious personal eye injury. Using The Grinder The Model H6156 is best suited for high RPM, low torque applications. Always test the bit and RPM combination on a scrap piece of material similar to the workpiece. Trial and error is the best way to determine the ideal setup. To use the grinder: 1. Grasp the grinder with a secure grip. 2. Rotate the speed lever to turn ON the mini grinder. 3. Adjust the speed lever to change the RPM. 4. Firmly grasp the grinder and ease it against the workpiece using light pressure. High RPM Uses High RPM's are best for general carving, cutting, routing, and grinding. The grinder remove material quicker at faster RPM's. Low RPM Uses Low RPM's are best for grinding and cutting materials that have low melting points. Plastics in particular often melt from the heat generated by high speed bits. Low RPM's are also best for polishing and buffing with the felt accessories included. Use low RPM settings when work- ing with plastics or other materi- als with low melting points. Melted plastics can liquefy, be thrown into the air, and stick to the operator, causing serious personal injury. Model H6156 Cordless Mini Grinder -7 Installing the Flashlight Base The flashlight base will give you the extra light that you need in low light situations. To install the flashlight base: 1. Unplug the tool from power! 2. Remove the collet shield. 3. Screw the flashlight base onto the mini grinder in place of the collet shield. 4. Turn the flashlight base ON/OFF with the small switch on the face of the flashlight base as shown in Figure 4. Figure 4. Flashlight base. Daily Maintenance These items should be done after each use. 1. Wipe the motor housing and tool bits with a dry cloth or blow off dust and debris with compressed air. 2. Check for damage to bits, cords, or the housing. -8- Model H6156 Cordless Mini Grinder NOTES Model H6156 Cordless Mini Grinder -9 H6156 Cordless Mini Grinder Parts Breakdown 1 2 8 3 4 5 6 7 REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 PH6156001 PH6156002 PH6156003 PH6156004 PH6156005 PH6156006 PH6156007 PHTEK3 UPPER HOUSING LOWER HOUSING COLLET LOCK COLLET SHIELD COLLET COLLET NUT ARMATURE TAP SCREW #5 X 1/2 -10-Model H6156 Cordless Mini Grinder 9 10 1112 13 14 15 16 REF PART # DESCRIPTION 9 PH6156009 10 PH6156010 11 PH6156011 12 PH6156012 13 PH6156013 14 PH6156014 15 PH6156015 16 PH6156016 A/C ADAPTOR BATTERY CHARGER BATTERY MINI GRINDER FLASHLIGHT BASE TOOL ASSORTMENT BAG SANDING ASSORTMENT BAG TOOL BIT ASSORTMENT BAG Model H6156 Cordless Mini Grinder -11 WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spec...