Votes - 2, Average rating: 4 ( )

Manafacture: Woodstock File size: 3.84 mb File name: m1051_m.pdf Language of manual:

1. Open circuit in motor or loose connections. 2. Start capacitor is at fault. 3. Short circuit in motor or loose connections. 4. Incorrect fuses or circuit breakers in power supply. 1. Inspect/repair all lead connections on motor for loose or open connections. 2. Replace start capacitor. 3. Inspect all connections on motor for loose or shorted terminals or worn insulation. 4. Install correct fuses or circuit breakers. Motor overheats, stalls (resulting in blown fuses or tripped circuit). 1. Motor overloaded. 2. Short circuit in motor or loose connections. 3. Depth of cut too great. 1. Reduce load on motor. 2. Inspect connections on motor for loose or shorted terminals or worn insulation. 3. Slow down the rate of movement of the workpiece into wheel. Wavy condition on surface of workpiece. 1. Machine vibrating. 2. Workpiece is not held in place- firmly. 3. Wheel face uneven. 4. Wheel is too hard. 1. Make sure machine is securely mounted on a solid surface. 2. Use a holding device to firmly retain the workpiece. 3. Dress the grinding wheel. 4. Use softer wheel, or reduce the feed rate. Lines on surface of workpiece. 1. Impurity on wheel surface. 2. Workpiece not being held tightly. 1. Dress the grinding wheel. 2. Use a holding device to firmly retain the workpiece. Burning spots or cracks in the workpiece. 1. Improper type of grinding wheel. 2. Improper feed rate. 3. Coolant required. 1. Try a wheel which is softer style or a coarser grit. 2. Slow down the rate of movement of the workpiece into wheel. 3. Add optional coolant system or introduce coolant by hand. Wheel dulls quickly, grit falls off. 1. Depth of cut too great. 2. Wheel is too soft. 3. Wheel diameter too small. 4. Bad wheel dress. 5. Defective wheel bonding. 1. Slow down the rate of movement of the workpiece into wheel. 2. Wheel too soft for the material being ground, select harder bond. 3. Replace the wheel. 4. Dress the wheel. 5. Consult manufacturer of grinding wheel. Wheel clogs and workpiece shows burn marks. 1. Wheel is too hard. 2. Feed rate too slow. 3. Bad wheel dress. 1. Wheel too hard for the material being ground, select softer bond. 2. Increase the rate of movement of the workpiece into wheel. 3. Dress the wheel. -15 MAINTENANCE -16- PARTS M1051 6" Bench Grinder .... .... .... .. .. .. .. .... .... .... .. .. .. .. .... .... .... .... .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .. .. .... M1051 Breakdown M1051 6" Bench Grinder REF PART..# DESCRIPTION REF PART..# DESCRIPTION 1 XM1051001 MOTOR..BODY 2 XPS05M PHLP..HD..SCR..M5-.8..x..8 3 XM1051003 STRAIN..RELIEF 4 XPWRCRD110L. POWER..CORD..110V..W/PLUG 5 XM1051005 NAMEPLATE..LABEL 6 XM1051006 WARNING..LABEL 7 XM1051007 SPARK..BREAKER 8 XPS05M PHLP..HD..SCR..M5-.8..x..8 9 XM1051009 MOUNTING..PLATE 10 XPW03M FLAT..WASHER..6MM 11 XPB18M HEX..BOLT..M6-1..X..15 12 XM1051012 BASE 13 XM1051013 RUBBER..FOOT 15 XPS09M PHLP..HD..SCR..M5-.8..X..10 16 XM1051016 BASE..PLATE 18 XM1051018 SWITCH..PLATE 19 XM1051019 SWITCH 21 XM1051021 STATOR 23 XPW02M FLAT..WASHER..5MM 24 XPLW01M LOCK..WASHER..5MM 25 XPS57M PHLP..HD..SCR..M5-.8..X..14 26 XPS07M PHLP..HD..SCR..M4-.7..X..8 27 XM1051027 CAPACITOR 28 XM1051028 ROTOR 29 XP6202 BALL..BEARING..6202ZZ 30 XM1051030 WAVY..WASHER 31 XM1051031 BEARING..HOUSING 32 XM1051032 WHEEL..COVER..RH..OUTER 33 XM1051033 WHEEL..FLANGE 34 XM1051034 WHEEL..NUT..RH 35 XM1051035 PAPER..DISC 36 XM1051036 GRINDING..WHEEL..60..GRIT 37 XM1051037 WHEEL..RIM..GUARD 38 XPS54M PHLP..HD..SCR..M5-.8..X..45 41 XPN06M HEX..NUT..M5-0.8 42 XPB06M HEX..BOLT..M8-1.25..X..12 44 XPW01M FLAT..WASHER..8MM 45 XM1051045 TOOL..REST..RH 46 XM1051046 EYESHIELD 47 XM1051047 WHEEL..COVER..LH..INNER 51 XM1051051 WHEEL..COVER..LH..OUTER 52 XM1051052 WHEEL..NUT..LH 53 XM1051053 GRINDING..WHEEL..30..GRIT 54 XM1051054 TOOL..REST..LH 55 XPW01M FLAT..WASHER..8MM 57 XM1051057 WHEEL..COVER..RH..INNER 58 XPLW04M LOCK..WASHER..8MM PARTS -17 Warranty Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility designated by our Bellingham, WA office, with proof of their purchase of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted...

Download now

Please, enter two numbers from picture: