Connect your ADSL line to this port. 2 Power Inlet Connect the included power adapter to this inlet. Warning: Using the wrong type of power adapter may damage the ADSL Wireless Base Station. 3 Reset Button Use this button to reset the power and restore the default factory settings. To reset without losing configuration settings, see ‘Reset’ on page 28-29. 4 On/off Button to switch unit on/off. 5 LAN Ports 10/100 Ethernet ports (RJ-45). Connect devices on your local area network to thes

Date/ Time SettingYou can change time setting from this page. Clicks “Apply” to save the setting. By default SNTP is set to Network Time Service otherwise select synchronize to PC. If internet access is available, we recommended setting SNTP to Network Time Service instead. IP Configuration By default, “IP Config” is set to “Automatic IP”. This will allow the NAS adapter to obtain its IP address automatically. If you prefer setting it manually, select the static IP option, enter your own value a

THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT. CAUTION: TO PREVENT ELECTRICAL SHOCK, THIS EQUIPMENT REQUIRES A GROUNDING CONDUCTOR IN THE LINE CORD. THE LINE CORD PROVIDED WITH THE EQUIPMENT IS ACCEPTABLE FOR USE WITH NEMA STYLE 5-15R AC RECEPTACLE SUPPLYING NOMINAL 120 VOLTS. DO NOT CONNECT THE PLUG INTO AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE PLUG CAN BE FULLY INSERTED WITH NO PART OF THE BLADES EX

.. . . .. . . .. . . .. . . .. 4 Installation Guide . . . . . . . . . . . . . . . 8 Step 1. Driver Installation . . . . . . . . . . . . . . . 10 Step 2. Plugging In the Hardware . . . . . . . . 12 Software Installation . . . . . . . . . . . . . . . . . 14 Ulead VideoStudio 8 . . . . . . . . . . . . . . . . . 15 French Manual . . . . . . . . . . . . . . . . . 31 Help Resources . . . . . . . . . . . . 58 Service and Warranty . . . . . . . . . . . . . . . 59 FCCInformation . . . . . . . . . . . . .

All rights reserved. No part of this documentation or software may be reproduced or distributed in any form without prior written permission from ARESCOM, Inc. ARESCOM, Inc. has the right to make revisions and to change the contents of this document without any obligation to provide prior notice of such revisions and changes. ARESCOM, Inc. provides this documentation without any kind of warranty, either expressed or implied, including but not limited to the implied warranties of merchantability

The Compact Flash should be keyed to prevent the card from being incorrectly inserted. 2. Put the mechanism in the open position and slide the flat ribbon cable into the ZIF connector on the adapter. 3. Close the latch to secure the ribbon cable connection. 1.8” ZIF- CF adapter shown below attached to a 1.8” ZIF to 2.5” IDE converter 1.8” ZIF- CF adapter shown below connected to a 2.5” drive enclosure TECHNICAL SUPPORT Email: Internet: Technical Support (8:30 am to 6:00 pm PST) Phone: 4

Insert Host Controller Driver Disk into CDROM. b. The Addonics Technologies Driver Disk window pops up. c. Select Configuration Utilities. Sil5744 SteelVine Manager. To extract the utility select your operating system from the list. d. Extract the files into your system. e. Install SiI5744 Manager by clicking the 5700Package.msi. Follow the instructions. f. After software installation, run the SteelVine Manager. The 57xx SteelVine Manager Utility manual can found in the Driver Disk under User Gu

Clare, Ireland Phone: +353.61.702042 Fax: +353.61.702001 Southern Europe and MEA Office 51-55 me Hoche 94200 Ivrysur Seine, France Phone:+331.43.90.19.20 Fax:+33 1.46.58.67.06 Installation Guide O System Requirements Requirements: • IBM Compatible PC or MAC* with available USB 1.1 or USB 2.0 port •Available FireWire port • USB 2.0 Host controller requires USB drivers from Microsoft (WinXP) or third party drivers shipped with USB Host controller card. NOTE: • For FULL USB 2.0 bandwidth

When Windows boots up, “A New Hardware Found” pops on the screen and the Addonics Serial ATA CARDBUS Controller is identified. 2. At the “Add New Hardware Wizard Window, click “Next” 3. Choose “Select for the best driver for your devices”, and click “Next” 4. Insert the Drivers Diskette or Driver Disc and check the “Floppy Drive or CDROM Drive” option. Click “Next” 5. If using a driver that has not been digitally signed by Microsoft, you will be asked if you want to continue the installation

Insert the Gigabit Ethernet ExpressCard Adapter to the system’s ExpressCard slot. Windows 2000, XP & 2003 Driver Installations 1. The Found New Hardware Wizard pops on the screen. Place the Addonics driver disk into the CDROM drive. 2. Found New Hardware Wizard: Can Windows connect to Windows Update to search for software? Select “No, not at this time” Click Next. 3. The Generic Marvell Yukon Chipset base Ethernet Controller is identified. 4. Found New Hardware Wizard: What do you want the