Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
NOTES:
1 HP recommends adapters in Superdomes be installed or replaced by a field service representative only.
2 Provided the server slot also supports OLAR or OL*.
3 HP-UX
After you view the table to determine the correct product configuration, check the driver release notes for your driver version to see if any patches are required.
To access Release Notes, go to: http://docs.hp.com under I/O Cards and Networking Software.
To access patches and download HP Integrity system firmware, go to: http://software.hp.com or http://itrc.hp.com
Select
Select patch
database,
database and
,
search
for
t he
the patch
num
ber.
ber I
. fIf not
already
registered,
registered y
, ou
yo c
an
can register
for
f ree
free o
n
on t he
the IT
RC hom
e page.
page.
The HP-UX drivers for the products shown in this matrix are distributed on HP-UX server and workstation Release Media and are installed with an Operating Environment. However, some of the products and drivers listed may be newer
than your system’s Operating Environment.
4 HP recommends that HP-UX 11i v3 users update to the newest available system and adapter firmware.
5 Supports up to two (2) small form factor (SFF) SAS hot-plug hard drives.
6 Requires the following minimum software versions: SerialSCSI-00 B.11.23.0712, CommonIO B.11.23.0712, Ignite-UX C.7.4.157.
7 Requires the following minimum software versions: SerialSCSI-00 B.11.31.0712, CommonIO B.11.31.0712, Ignite-UX C.7.4.157.
8 E
EFI
F d i
I driver ve i
3 03 05
l
i
i d f
b
T
rsion 3.03.05 or later is required for boot support. T
b
i
d
ape boot is not supported.
9 Only dual-ported A/A disks are supported in MSA enclosures.
10 MSA50 is supported on HP-UX only. (No OpenVMS, Windows or Linux support)
11 MSA60 and MSA70 require the MSA IO Module, Option Kit # AG779A, for use with the AH303A. (No Windows or Linux support)
12 AH303A requires VMS831H1I_FIBRE_SCSI-V0100 and VMS831H1I_IPB-V0100 patch kits or later.
13 HP-UX 11i v3: Ultrium-3 and Ultrium-4 tape drives require SerialSCSI-00 B.11.31.0712 or later; MSL2024, MSL4048, MSL8096, 1/8G2 autoloader, and DAT160 tape drive require SerialSCSI-00 B.11.31.0803 or later.
HP-UX 11i v2: Ultrium-3 and Ultrium-4 tape drives require SerialSCSI-00 B.11.23.0712 or later; MSL2024, MSL4048, MSL8096, 1/8G2 autoloader, and DAT160 tape drive are not supported.
O
penVMS
penVM 8
3
. -
3 1H1
1H1 and
Linux:
A
ll
All exter
nal SAS
tape dr
ives s
upported.
14 Linux only supports tape connect. No support for MSA50, MSA60 or MSA70 with this controller.
Detailed information about slots in entry-level Integrity servers can be found at: http://www.docs.hp.com/en/SSM2-EL/slotmatrix.htm
Go to http://docs.hp.com under I/O Cards and Networking Software for matrices for other I/O cards and additional I/O card documentation.
Please send your feedback on this document at http://docs.hp.com/en/feedback.html
Legal
Legal Not
Notices
© 2004-2008 Hewlett-Packard Company, L.P. The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty.
HP shall not be liable for technical or editorial errors or omissions contained herein.
HP-UX® , and Superdome® are registered trademarks of the Hewlett-Packard Corporation.
All other trademarks and registered trademarks are the property of the respective corporations.
HP SAS Host Bus Adapter Support Matrix
Page 2 of 2