Votes - , Average rating:
(
)
)
Manafacture: Abocom
File size: 549.97 kb
File name: d650e4b6-bf10-5474-4151-7267d09b3b59.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
See the following illustration for the location of the connectors described in the following table. 5VDC • Switch Console Ethernet aqsl Ш I R J* ® vv.v.v • a m_m V Connectors on the rear panel Connector Label Connector Description 5VDC 5VDC Input Power Connector Switch POWER ON/OFF SWITCH Reset System Reset. Console Connects this device to the serial port on your PC. USB USB INPUT PORT Ethernet Connects to the Ethernet port on your PC using the Non Hub Ethernet cable supplied with your unit, or LAN hub using a straight-through cable. ADSL Connects this device to the wall jack. - 2 - Setting Up the Hardware Environment Connecting All Cables to the Network Perform the following procedures to set up the ADSL ROUTER. Step 1 Connect the power adapter to the port labeled 5VDC on the rear panel of this device. Step 2 Connect the Ethernet cable. One PC - ADSL Router (direct connection) If your only have one PC, you can connect your ADSL ROUTER to the PC directly without a hub. For a single Ethernet-equipped PC, use the "non-hub" twisted-pair crossover cable to connect the ADSL ROUTER Ethernet port to the Ethernet port on your computer. Home Network - ADSL Router (connection through Ethernet Switch/Hub) If your ADSL ROUTER is connected to a home network, you may use a standard Ethernet cable (not provided) to connect your ADSL ROUTER Ethernet port to an available port on your home network Ethernet hub. Step 3 Connect the ADSL cable to the ADSL ROUTER. Connect the ADSL ROUTER to the ADSL line with the provided telephone cable. - 3 - Step 4 Connect one end of RS-232 cable to any free COM port in your system; Connect the other end to “Console” port on the rear panel of the ADSL router. Powering On the ADSL ROUTER Step 1 Connect the power adapter to your ADSL ROUTER by plugging one end of the power supply into an appropriate electrical outlet and the other end into port labeled 5VDC on the rear panel of the device. Note: To power off he ADSL ROUTER, just unplug the power supply cable from the ADSL ROUTER rear panel POWER connector. Step 2 Once your ADSL ROUTER is powered up, check to make sure the Power LED is red and ON. Step 3 If the Power LED is not lit, immediately turn off all power to the ADSL ROUTER. - 4 - INTERNET ACCESS Router Mode/ IP over ATM (RFC1577) (1) Run the “router.exe” file saved in the configuration utility. (Go to Start ^Program^ ADSL Router xx Configuration Utility^ Configuration Utility.) (2) Select a PC COM port available on your computer used to connect to the ADSL Router’s “Console” port. (3) Check “Router Protocol” and select “IP over ATM”. (4) Click “Properties” button. Setcil Configure*« (• Make anew seWng p -Set ADSL Router дз Router or В ridge Mode ErcapsUUcr Mrt'cd G PoUti ЦИЫМ1!1-Д1Д _-J Pioperties | (~ Bndge АооЦш • J Г ADSL Pvameta |h JtMode Seve above ihe «ilng m ' and lie Use ptewxjs sdmg I Ng.i ■ I Cancel (5) Enter “ADSL IP”, “Gateway IP”, and “Subnet Mask” addresses provided by your service provider. (6) Usually Ethernet IP addresses were not provided by service providers. Check to make sure if this is your case, if yes, remember to select “Enable NAT function.” (7) Enter the VPI and VCI numbers. Typically VPI is set to “0”. - 5 - ill WAN Port Setting ADSL IP I 10 . 1 . 1 . 1 Gateway IP | 10. 1 Subnet mask VPI [Ö I 255. 255. 255. 0 VCI [S8 I- Obtain an IP address automatically Ethernet IP I 10 . 0 . 2 Subnet mask j 255. 255. 255. (* Disable DHCP Server ~C Enable DHCP ServerStart IP I 0.0.0 0 . 0 . 0 . 0 DNS IP I- Telent Enabled F ¡Enable NAT function T elnet Password (8) Click “OK” to go to “Select Config” menu. Or click “Save As File” to save the settings for future use. Then click “Next”. (9) Click “Configure” button. The configure utility will automatically setup the router for you. Expect a minor delay for configuration. Bridge mode/RFC1483 bridge (1) Run the “router.exe” file saved in the configuration utility. (Go to Start ^Program^ ADSL Router xx Configuration Utility^ Configuration Utility.) (2) Select a PC COM port available on your computer used to connect to the ADSL Router’s “Console” port. (3) Click “Next” button. (4) Select Mode “Bridge” and select “RFC1483 Bridge”. Miÿ * n ryw P Set ADSL Router js Router or Bridge Frr*nii*nn Rout« |Fff (• Bldsa S«"** dtv** •» ' c»wJ li* Um ntvoi MttoQ « 6ac» I Nee > j Caned (5) Click “Properties” button. - 6 - RFC1483 Bridge Setting VF4 fÔ VCI [Ж <* Disable HTTP r Enable HTTP HTTP IP j" 0 G G G Г Telent Enabled Password LLC Encapsulation C VC based Route VC based Biidge Cancel | (6) Enter VPI and VCI numbers. Then click “OK”. (7) Check “LLC Encapsulation” or “VC Based Route” or “VC Based Bridge”. (8) Click “Next” followed by “Configure”. Configure utility will automatically setup the router for you. Expect a minor delay for the router configuration. (9) Click “Finish”. Now you have finished ADSL Router configuration. The ADSL Rou...