Login:
Votes - 3, Average rating: 4.3 ( )

User manual ADIC, model SNC 5100

Manafacture: ADIC
File size: 806.62 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


For more information, see the ADIC Management Console User Guide. The ADIC Management Console service port supports Zmodem file transfers. The procedures below are specific for using the HyperTerminal program on the service terminal to transfer files. Other terminal emulation programs operate in a similar fashion. The Zmodem send and receive functions in some terminal emulation programs automatically issue the command string “rz” before sending a file and the command string “sz” before receiving a file. However, even if the program you are using automatically sends the “rz” command, manually issuing the command string “rz” before starting the transfer has no negative effect on the transfer. Updating SNC 5100 Firmware Step 1. From the Hyper Terminal window, at the SN60023 > command prompt, type rz and then press the Enter key. Step 2. From the HyperTerminal window select Transfer and Send File. Step 3. From the Send File dialog enter the path and filename where the firmware file is located or click the Browse button and navigate to it. Step 4. In the Protocol field, select Zmodem and click the Send button. Step 5. It will take several minutes for the file to be transferred. The Zmodem file send dialog will display the current status and it will close automatically when the file transfer has completed. Step 6. Wait for the Firmware Update Complete status message to be displayed on the service terminal indicating successful completion. Step 7. Reboot the SNC 5100 for the update to take effect. For more information, see the "reboot" command on page 151. Updating Firmware and Configurations 6-00020-02 SNC 5100 If HyperTerminal reports an error, try to send the file again. If the SNC 5100 reports an error, make a note of the error code and see the Table 12, “Zmodem Status Codes,” on page 100 for further information. Saving a Configuration File Step 1. From the HyperTerminal window enter sz “config.cfg” . The filename “config.cfg” is an example of a name. You can specify a different filename but it must be in quotes, it must be 8 characters or less and it must end in .cfg. Step 2. From the HyperTerminal window select Transfer and Receive File. Step 3. From the Receive File dialog enter the path to the folder where you want to save the file or click the Browse button and navigate to it. Step 4. For the Receiving protocol select Zmodem and press the Receive button. Step 5. Wait for the “Configuration Download Complete” status message to be displayed on the service terminal indicating successful completion. If HyperTerminal reports an error, try to receive the file again. If the SNC 5100 reports an error, make a note of the error code and see the Table 12, “Zmodem Status Codes,” on page 100 for further information. Loading a Configuration File Step 1. From the Hyper Terminal window, at the SN60023 > command prompt, type rz and then press the Enter key. Step 2. From the HyperTerminal window select Transfer and Send File. 6-00020-02 Updating Firmware and Configurations SNC 5100 Step 3. From the Send File dialog enter the path and file name where the firmware file is located or click the Browse button and navigate to it. In the Protocol field, select Zmodem and click the Send button. Step 4. Wait for the “Configuration Update Complete” status message to be displayed on the service terminal indicating successful completion. Step 5. Reboot the SNC 5100 for the update to take effect. For more information, see the "reboot" command on page 151. If HyperTerminal reports an error, try to send the file again. If the SNC 5100 reports an error, make a note of the error code and see the Table 12, “Zmodem Status Codes,” on page 100 for further information. Zmodem Status Code Table The following table shows Zmodem status codes reported by the SNC 5100. Table 12: Zmodem Status Codes Status Code Description 0 OK -1 Error unwrapping file -bad file, or out of space -2 Error opening file -3 Error writing file -4 Error closing file -5 Service Port Function Only -6 Cannot create Debug file - only applicable under lab conditions -7 Cancelled by host -8 “Command” not supported -9 Memory Buffer allocation failed - problem with SNC 5100 memory allocation -10 No file to send -11 Garbage - degraded link 100 Updating Firmware and Configurations SNC 5100 Table 12: Zmodem Status Codes Status Code Description -12 CRC Error - degraded link -13 Timeout Error -14 File size error - file size is different than it was supposed to be -15 Invalid file type -16 Too many retries - degraded link -17 Position Error - file data has been lost Setting the Time and Date Setting the Real Time Clock Step 1. Use the rtcDateSet command to manually set the Real Time Clock. For more information, see the "rtcDateSet[year],[month],[dayofmonth],[dayofweek], [hour],[minute],[second]" command on page 154. Example: SN60023 > rtcDateSet 2001,1,26,5,9,30,00 value=0=0x0 SN60023 > Step 2. Use the dateSetFromRTC command to set the SNC 5100’s RTC as the source of date display...

Other models in this manual:
Network Equipment - Scalar 1000 (806.62 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category