Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
B. After making all entries using the Quick Start setup procedures, press X to return to the Quick Start menu screen. Or, to verify the status of the ER and review the entries you made using the Quick Start setup, press 1 to view the System Status screen. NOTE: Changing your password using option C, “Change Quick Start password”, will change the password for the console menu but not the ER console login screen. Option A, “Reset system to factory defaults”, should only be used by an 8e6 Technologies technical representative. Option D, “Reset admin console account”, should be used for resetting the administrator console username and password to the factory default ‘admin’/’reporter’ and for unlocking all IP addresses currently locked. System Status screen The System Status screen contains the following information: Capturing Interface specified in screen 3 (Configure network interface LAN1) lan1 IP address and netmask specified in screen 3, and current status (“Active” or “Inactive”) Default gateway IP address specified in screen 4 (Configure default gateway) ER host name specified in screen 6 (Configure host name) DNS server IP address(es) specified in screen 5 (Configure DNS servers) Regional timezone setting specified in screen 7 (Time Zone regional setting) Current status of the ER Current ER software Version installed NOTE: Modifications can be made at any time by returning to the specific screen of the Quick Start procedures. Log Off, Disconnect the Peripherals A. After completing the Quick Start setup procedures, return to the Quick Start menu screen and press 9 to log out. B. Disconnect the peripherals from the ER. Step 1B: Console Setup Procedures Preliminary Setup Create a “setup workstation” using a Windows-based laptop or desktop machine with a network card and Internet Explorer 6.0 (or later). The setup workstation will be used for accessing the ER server on the network and configuring the unit. Workstation Configurations A. From the desktop of the setup workstation, follow the procedures for your machine type: Windows XP - go to Start > Control Panel. Open Network Connections. Right- click the link for LAN or High-Speed Internet and choose Properties. Windows 2000 - right-click the My Network Places icon and select Properties. Right-click the correct Local Area Connection and choose Properties. Windows NT - right-click the Network Neighborhood icon and select Properties. Windows ME - right-click the My Network Places icon and select Properties. B. Click on Internet Protocol (TCP/IP) to highlight it (Windows NT and ME users should select the Protocols or Configuration tab and choose TCP/IP Protocol). C. Click the Properties button. WARNING: Be sure to make note of the current network settings on the setup workstation as you will need to return them for further setup procedures. D. Choose the option Use the following IP address (Windows NT and ME users should choose the option Specify an IP Address). E. Type in the IP address of 1.2.3.3. F. Type in the Subnet mask (netmask) of 255.0.0.0 and click OK. G. Close the LAN connection properties box. Storage Device Setup (for Attached Storage Units) If you have a NAS (SCSI Connected Storage Device or “SAN”) that will be used with the ER, you will need to connect it to the ER at this point. Refer to the Appendix at the end of this document for instructions on how to connect the SCSI Connected Storage Device. Link the Workstation to the ER The procedures outlined in this sub-section require the use of the CAT-5E crossover cable. A. Plug one end of the CAT-5E crossover cable into the ER’s LAN 1 port. NOTE: When facing the rear of the chassis, the LAN 1 port is the port on the left. Portion of SL chassis rear Portion of HL chassis rear B. Plug the other end of the CAT-5E crossover cable into the setup workstation’s network card. NOTE: If a CAT-5E coupler was packaged with your unit, this coupler can be used if the crossover cable is not long enough for your setup. Plug one end of the CAT-5E crossover cable into the ER, and the other end into the coupler. Plug a standard CAT-5E cable into the other end of the coupler, and the free end of the standard CAT-5E cable into the setup workstation. C. Plug the ER into a power source with an appropriate rating. WARNING: It is strongly suggested you use an uninterruptible power supply. D. Power on the ER by lowering the bezel and pressing the large button at the right of the front panel (see diagrams below): Diagram of SL chassis front panel, power button at far right Diagram of HL chassis front panel, power button at far right WARNING: The ER is an information database. If you experience a power interruption or power off the ER in any manner other than from the Web-based interface utility described in the sub-step Physically Connect the ER to the Network, you may lose data and/or damage the file system. The Boot Up Process The boot-up process may take 5 - 10 minutes. When the drive light remains off for 30 seconds, th...
Other models in this manual:Network Equipment - Enterprise Reporter HL-002-002 (3.17 mb)
Network Equipment - Enterprise Reporter HL-002-002 (3.17 mb)
Network Equipment - Enterprise Reporter HL-002-002 (3.17 mb)
Network Equipment - Enterprise Reporter HL-022-002 (3.17 mb)