Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
To setup Avenview FO-DVI-DL-330X follow these steps for connecting to a device: 1. Connect FO-DVI-DL-330X Transmitter unit to DVI source 2. Connect FO-DVI-DL-330X Receiver unit to DVI port of display. 3. Connect 2 Strand Fiber Optic LC Type cable to both Transmitter and Receiver. 4. Plug the power to Receiver Unit. 5. Power on DVI Source and DVI Display. Use the DC adapter (included in the package) for the Receiver. The Transmitter which is connected to a computer uses power from the computer. If Transmitter power LED doesn’t light up after PC is turned on, then use the external power adapter for Transmitter. 1.9 Function Switch EDID: Switch in front of Transmitter - REAL: EDID data of connected monitor is transmitted between Transmitter and Receiver in real time through UTP cable. - Emulation: Certain EDID data pre-set in the Transmitter is used in signal transmission. UTP cable is not necessary. MODE: Switch in front of Transmitter - Single: When you use Single link display (up to 1920 x 1200), select ‘Single’ switch. - Dual: When you use Dual link display (2560 x 1600), select ‘Dual’ switch. 1.10 General Troubleshooting Problem Possible Solution Power ON Power LED does not work . Please check out voltage of adapter. (DC +5V) . Ensure that power adapter correctly plugged Cannot read selected EDID . Select switch the emulation mode - Retry self EDID read - Check the monitor to read EDID . Select switch the real mode. - Please check and connected the UTP cable. (Only the direct type) - Please check if the DVI cable is connected. Resolution Issue . Select single mode switch - Max resolution 1920x1200@60Hz - Some monitor will not support this mode. . Select dual mode switch - Max resolution 2560x1600@60Hz - Please check and connect DVI cable type (Should use DVI-Dual cable) . Noise or no display - Please check the DVI and optical fiber cable is connected. *** The max resolution is different on to connected monitor Self EDID Setting : 1) DDC function switch set to Emulation. 2) DVI cable connection between TX and display. 3) Supply power to TX (DC +5[V]). 4) LED blink -> LED ON Section 2: Specifications Item Description Units FO-DVI-DL-330X (Transmitter) FO-DVI-DL-330X (Receiver Unit Description DVI Dual Link Transmitter DVI Dual Link Receiver Input Signal TMDS Signal (DVI 1.0 Standard) Output Signal TMDS Signal (DVI 1.0 Standard) Video Bandwidth 1.65Gbps (Single Link) Supported Resolution & Distance Single Link: WUXGA 1920 x 1200 @ 100 meters ( 330 feet) Dual Link: WQXGA 2560 x 1600 @ 100 meters (330 feet) Optical Converter 2 ch 850 nm Multi-Mode VCSEL 2 ch GaAs PIN photo Diode DVI Connector 24 pin DVI-D Plug Optical Connector 2 LC Connector DDC Link Connector Rj45 Fiber Type 62.5/125 .m Multi-mode glass fiber Dimensions (L x W x H) 3.4” x 5.3” x 1” Power Supply 5V 2A DC Power Consumption 1.5W (max) Environmental Operating Temperature 32. ~ 104.F (0. to 40.C) Storage Temperature -4. ~ 140.F (-20. ~ 60.C) Relative Humidity 20~90% RH (no condensation) 2.1 Signal Pin Assignment (Single Link) TRANSMITTER Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield 4 No Connect 12 No Connect 20 No Connect 5 No Connect 13 No Connect 21 No Connect 6 DDC Clock (SCL) 14 +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data (SDA) 15 Ground (for +5V) 23 T.M.D.S. Clock+ 8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock- RECEIVER Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield 4 No Connect 12 No Connect 20 No Connect 5 No Connect 13 No Connect 21 No Connect 6 DDC Clock (SCL) 14 Out +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data (SDA) 15 Ground (for Out +5V) 23 T.M.D.S. Clock+ 8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock- 2.2 Signal Pin Assignment (Dual Link) TRANSMITTER Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield 4 T.M.D.S. Data4- 12 No Connect 20 T.M.D.S. Data5- 5 T.M.D.S. Data4+ 13 No Connect 21 T.M.D.S. Data5+ 6 DDC Clock (SCL) 14 +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data (SDA) 15 Ground (for +5V) 23 T.M.D.S. Clock+ 8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock- RECEIVER Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield 4 T.M.D.S. Data4- 12 No Connect 20 No Connect 5 T.M.D.S. Data4+ 13 No Connect 21 No Connect 6 DDC Clock (SCL) 1...