Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
. . . . . . . . . . . . . . . . .2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4 Installation Instructions . . . . . . . . . . . . . . . . . .5-12 Cleaning and Maintenance . . . . . . . . . . . . . . . . . .13Assembly of Components . . . . . . . . . . . . . . . .14-16Solenoid Valve Troubleshooting . . . . . . . . . . .17-18Vernatherm™ Valve Maintenance . . . . . . . . .19-20 Cleaning the Strainer . . . . . . . . . . . . . . . . . . . .19-20 IMPORTANT Read this entire installation manual to ensure proper installation. Flush all the water supply lines before making connections. Wall anchors used must have a minimum pull-out rating of 1,000 lbs. File these instructions with the owner or maintenance department. Product warranties may be found under "Product Information" on our web site at P.O. Box 309, Menomonee Falls, WI 53052-0309 215-1480 Rev. E; EN 06-915 TEL. 1-800-BRADLEY FAX 262-251-5817 © 2007 Bradley Corporation Page 1 of 20 2/8/07 Express® Lavatory System - MG-Series with TouchTime® Control MG-2/TT Installation Instructions Pre-Installation Information Barrier-free and ADA compliant - standard height mounting The MG-2/TT Express® Lavatory System must have a rim height no higher than 34" above finished floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim height, the MG-2/TT Express® Lavatory System meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and controls. Always check local codes and ordinances for compliance. Barrier-free and ADA compliant - juvenile height mounting The MG-2/TT Express® Lavatory System must have a rim height no higher than 30" above finished floor to be compliant with Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities: Building Elements Designed for Children's Use; Final Rule. Texas Accessibility Standards compliant: The MG-2/TT Express® Lavatory System meets Texas Accessibility standards (TAS) for barrier-free clearances, reaches and controls. Always check local codes and ordinances for compliance. TouchTime® switch and solenoid Each sprayhead is controlled by a TouchTime® switch, enabling each user to activate a single flow of water. Each valve uses less than half the maximum of hot water allowed by the ANSI/ASHRAE/IESNA 90.1-1989 Standard. Supplies required for installation: • (8) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • 1/2" NPT hot and cold supply piping and 1-1/2" NPT drain piping • 1/2" NPT street elbow • 110 volt electrical outlet for 110/24 VAC plug-in transformer (supplied) • 240/208-volt or 277-volt electrical outlet for optional electric tankless water heater 2/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915 Express® Lavatory System - MG-Series with TouchTime® Control Installation Instructions MG-2/TT MG-2/TT Express® Lavatory System Dimensions 27" (686) 47" (1194) 54" (1372) 42" (1067) 15" (381) ADA COMPLIANT 22" (559) *39" (991) *33-1/2" (851) *29-1/2" (749) *17-1/2" (445) 21-1/2" (546) 9-1/2" (241) 15" (381) (mm) (mm) (mm) *Subtract 4" from vertical dimensions for compliance with ADA guidelines for children's use. Bradley Corporation • 215-1480 Rev. E; EN 06-915 2/8/07 Express® Lavatory System - MG-Series with TouchTime® Control MG-2/TT Installation Instructions Dimensions continued . . . 35-1/2" (902) 30" (762) 26" (660) 14" (356) FLOOR (mm) TAS Juvenile Height Grades Pre-K thru 5 or 6 37-1/2" (952) 32" (813) 28" (711) 16" (406) FLOOR (mm) TAS Juvenile Height Grades 6 thru 8 or 9 2/8/07 Bradley Corporation • 215-1480 Rev. E; EN 06-915 Express® Lavatory System - MG-Series with TouchTime® Control Installation Instructions MG-2/TT Installation Instructions Step 1: Rough in supplies and optional hot water heater NOTE: See Figure 1 (below), 1a, 1b (for TAS on page 6) and Figure 2 (on page 7) when roughing in the MG-2/TT Express®. IMPORTANT: Flush the supply lines before making connections. Debris in supplylines will cause the valves to malfunction. IMPORTANT: Dimensions shown in Figure 1 are for Standard Height Mounted MG-2/TT Express®. 1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown. 2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown. 3. OPTIONAL HOT WATER HEATER: Rough in appropriate electrical supply per local code (recommended 240/208-volt or 277-volt electrical box location shown below). 4" (102) 5" (127) FLOOR APPROX. DIMENSION 14" (356) 14" (356) *22-3/8" (568) *28-1/4" (718) *25-3/4" (654) 1/2" NPT HOT AND COLDSUPPLIES OR TEMPERED SUPPLY – STUB OUT 2" 1-1/2" NPT DRAINSTUB OUT 2" 110V GFI PROTECTED ELECTRICAL OUTLET 3/8" WALL ANCHORS (8) PLACES MIN. PULL-OUT STRENGTH 1000 LBS. PER ANCHOR *Juvenile Height Mounting: Subtract 4" from vertical dimensions for compliance with ADA guidelines for children's use. Figure 1 Standard Height Mounting CENTERLINE OF FI...