Votes - 2, Average rating: 5
(
)
)
|
manual abstract
A blade with worn teeth besides providing poor performance might also generate a sudden thrust. This can result in a violent sideways kick caused when the blade touches against wood or solid bodies, such thrust might then cause the operator to loose control of the machine itself. Never attempt to work with a damaged blade but replace it with a new one. THRUST: can occur when using any type of circular blade within the risk area: therefore it is advisable to cut using the remaining area of the blade. CIRCULAR SAW BLADE: it can be used to cut sappling, small trees with a diameter up to 7 cm., to clean shrubs. WARNING: IF A METAL 24-80 TOOTH BLADE IS USED (A TOOTH SAW BLADE) A DOUBLE SHOULDER HARNESS AND A SAFETY A GUARD (PROTECTION) MUST ALSO BE USED AUTHORISED SERVICING DEALERS. AS MARKED IN THE SUMMARY CHART (SEE THE USE OF NON-ORIGINAL ACCESSORIES CLOTHES SECTION IN SAFETY CHAPTER: AND SPARE PARTS INCREASES THE RISK OF ALWAYS WEAR A HELMET). ACCIDENTS AND IN SUCH A CASE THE COMPANY IS NOT LIABLE FOR DAMAGE TO ALWAYS USE GENUINE ACCESSORIES AND PEOPLE AND/OR THINGS. SPARE PARTS AVAILABLE FROM D. FUEL MIX Use only fuel recommended by this manual. This product is fitted with a 2-stroke engine and therefore requires a 2-stroke petrol and oil mix. Use unleaded petrol with a minimum octane rating of 90. Only use oil from sealed containers. In order to obtain a good fuel mix, put the oil into the container before the petrol. The use of sub-standard petrol or oil may reduce performance or reduce the life of certain components. UNLEADED PETROL If using unleaded petrol, you must use a totally synthetic 2-stroke engine oil or branded 2-stroke engine oil, see table. IMPORTANT Always shake the fuel mix container thoroughly before pouring any fuel mix. Fuel mix properties may deteriorate with time and should be used up within 2 months. We recommend that you prepare fuel mix according to your immediate requirements only. Never use fuel mix more than 2 months old so as to avoid possible engine damage. WARNING Do not smoke when re-fuelling. Always open the fuel cap slowly, to release any pressure build up in the tank. Re-fuel in open spaces only, keeping away from naked flames or sparks. SAFE STORAGE OF FUEL Petrol fuel mix is highly inflammable. Put out all cigarettes, pipes and cigars before working with fuel. Avoid spilling fuel. Store fuel in a cool, well ventilated place, in an approved container specifically designed for the purpose. Never store engine with fuel in the tank in enclosed, poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light such as in a furnace, water heater, clothes dryer etc. Petrol fumes can cause an explosion or a fire. Never store large amounts of fuel. To prevent possible restarting problems avoid running the fuel tank dry. This also helps to extend engine life. E. SAFETY GUARD ASSEMBLY 1) In the interest of safety, it is imperative that the Only use blades or nylon string heads clearly unit is used with the correct guard (P/N 247208) marked with a maximum speed of at least 10,500 when using any blade or a nylon string head, min-1. except the 24-80 tooth blade. Line cutter blade Follow the fitting instructions carefully. (L): assemble as illustrated. N.B: Saw tooth blades (24 - 80 tooth) have a 2) When using a saw tooth blade (optional central base diametre of 20mm and therefore accessory), the correct guard must be fitted (P/N require the use of the appropriate size top flange 240553). to ensure a correct fit. The part number is A double shoulder harness must also be worn. detailed in the cutting attachment summary chart. F. BLADE AND NYLON STRING HEAD ASSEMBLY Assemble the correct guard to suit the kind of Fixed mower gauge - f) Blade locking screw blade or nylon string head to be used (See (length mm 16). section: SAFETY GUARD ASSEMBLY). 2) If you want to assemble the rotating mower 1) Assemble blade as illustrated: gauge,proceed asillustrated: a) Flange guard - b) Upper cap with blade a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) arrow facing upwards - d) Lower washer - e) A Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Replace the blade attachment bolt if damaged in any way. 3) Make sure that the blade bore opening fits perfectly around the centering collar on the upper cap. Tighten counterclockwise. While tightening, the blade assembly can be held fast by inserting the wrench or the screwdriver supplied into the cap and gearcase holes. To do this, rotate the cap intil the two holes coincide. 4) Assemble nylon string head as illustrated: a) Flange guard - b) Upper cap - c) Guard d) Nylon string head Tighten counterclockwise. 5) While tightening, the head assembly can be held fast by inserting the wrench or the screwdriver supplied into the holes as already shown for blade assembly. WARNING: Pleas...