Votes - 4, Average rating: 4.3 ( )

Manafacture: MTD File size: 1.59 mb File name: 06207207-59e5-d9e4-71be-b29ca744b36b.pdf Language of manual:

Proper lubricant level should be up to the front pipe plug. Check with tiller on a level surface. Add lubricant through vented pipe plug hole. Add enough to bring level up to front pipe plug hole. Use Mobilube SAE 140 gear oil or equivalent. Gear case should be maintained with five (5) ounces of lubricant. TILLER GEAR CASE BEARING ADJUSTMENT CAP (Small) If the bearing adjustment cap on the worm shaft is over-tightened the bearings on the worm shaft can seize during operation. The cap should protrude approximately 1/32" to 1/16" from the gear case. REPLACING TILLER GEAR CASE OIL SEALS 1. Drain lubricant. 2. Remove tine assemblies. 3. Remove bearing cap. (See reference 24, page 10.) 4. Remove bearings, worm wheel and tine shaft. Do not remove bearing races. 5. Remove oil seals from gear case and bearing cap. 6. Remove all burrs from holes in tine shaft. 7. Dip oil seals in lubricant and then insert one in gear case and one in bearing cap. 8. Wipe tine shaft clean of filings and lubricate before assembling with bearings and worm wheel in gear case. Insert shaft slowly to prevent seals from catching in holes in shaft. 9. Replace bearing cap. CAUTION Do not damage oil seals. The open flanges face to the outside of the gear case. 10. Tighten bearing cap, retighten screws evenly. 11. Replace tine assemblies and add lubricant. (See gear case above.) 6 2. Unhook belt from engine pulley and gear case pulley. 1. Remove Belt Guard. Gear Case Pulley 3. Assemble New Belt. I BELT REMOVAL REVERSE DRIVE 4. Remove Hex Nut and Idler Pulley. 5. Unhook Reverse Drive Beit from Gear Case Pulley. Engine Pulley 3. Unhook Forward Drive Belt from Engfme Pulley and Gear Case Pulley. 1. Remove Belt Guard. 6. Assemble new Belt. Reverse Steps 1 through 5. Gear Case Pulley 2. Remove Lower Belt Guard. 8 REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 716-0119 2 721-0100 3 748-0106 4 717-0226 5 737-0102 6 741-0107 7 711-0469 8 738-0170 9 717-0312 10 716-0101 11 735-0100 12 10583 13 714-0474 14 714-0126 Snap Ring for .750" Dia. Shaft Oil Seal—.750" Shaft Sleeve Brg. .752" I.D. Gear Case Sq. Hd. Pipe Plug with Vent %" Thd. Roller Brg. .750" Bore Spacer .755" I.D. x 1.265" O.D. Worm Shaft %" Dia. Worm (Stencil "20") Snap Ring for .750" Dia. Shaft O-Ring 2.12 x 2.38 Brg. Adjustment Cap Cotter Pin W Dia. x .75" Lg.* #9 Hi-Pro Key 3/16 x%" Dia. Hdn. 15 737-0103 16 721-0102 17 741-0108 18 711-0131 19 711-0133 20 714-0103 21 716-0102 22 717-0315 23 735-0101 24 717-0227 25 736-0119 26 710-0371 Sq. Hd. Pipe Plug %" Thd. Oil Seal Double Lip 1" Shaft Roller Brg. 1" Bore Spacer 1.005 I.D. x 1.390 O.D. Tine Shaft 1" Dia. #91 Woodruff Key WxW Dia. Snap Ring for 1" Shaft . Worm Wheel (Stencil "20") O-Ring 3.62 x 3.88 Bearing Cap—Bolt-on Type L-Wash. 5/16" Scr.* Hex Scr. 5/16-18 x.88" Lg.-Special *For faster service obtain standard nuts and bolts locally. If that* Items cannot ba obtained locally, order by part number and size as shown on the parts list. 9 I IF YOU WRITE TO US ABOUT THIS ARTICLE OR IF YOU ORDER REPLACEMENT PARTS ALWAYS MENTION THIS MODEL & SERIAL NO MODEL 215-355AB2 215-360AB2 10 215- 355AB2 PARTS LIST FOR MODELS 215-355AB2 AND 215-360AB2 REF. PART COLOR NEW REF. PART COLOR NEW NO. NO. CODE DESCRIPTION PART NO. NO. CODE DESCRIPTION PART 1 2 01166 04626-458 Grip Handle Ass'y. 28 712-0267 Hex Nut 5/16-18" Thd.* 3 746-0244 Throttle Control Ass'y -"—^Comp. 29 736-0119 L-Wash. 5/16" Scr.* 4 07470 Throttle Control Knob 30 04631-458 "U" Channel Brkt. Ass'y. 5 746-0243 Conduit and Wire 31 710-0152 Hex Scr. %-24x 1.00" Lg.* 6 11598 Throttle Control Ass'y. 32 04633-458 Tiller Frame 7 04638-458 Handle/Wheel Brkt. Ass'y. R.H. 33 710-0198 Hex Sems Scr. 5/16-18 x.75" 8 736-0169 L-Wash. %" Scr.* Lg.* 9 712-0798 Hex Nut %-16 Thd.* 34 710-0451 Crg. Boit 5/16-18 x.75" Lg.* 10 04637-458 Handle/Wheel Brkt. Ass'y. L.H. 35 04602 "U" Clevis Pin .500" Dia. 11 712-0384 Hex Cent. Nut ’/2-13 Thd.* 36 715-0133 Spr. Pin Spiral 5/32" Dia. x 12 736-0253 'Bell Wash. .505 Î.D. .875" Lg. 13 710-0594 Adj. Screw N 37 736-0190 Ext. L-Wash. V2" Scr.* 14 736-0253 Belleville Wash. .505" I.D. x 38 712-0239 Hex Cent. Nut '/2-20 Thd.* 1.00" O.D. 39 712-0214 Hex Cent. Nut %-24 Thd.* 15 738-0239 Sh. Scr. %" Dia. x .222" Lg. 40 736-0148 Ext. L-Wash. %" Scr.* 16 741-0116 Flange Brg with Flats .631 I.D. 41 711-0392 Ferrule 17 734-0573 Wheel Ass'y. Comp. (360AB2) 42 711-0610 Control Rod 18 738-0240 Sh. Scr. %" Dia. x 2.75" Lg. 43 720-0143 Grip 19 734-0584 Wheel Ass'y. Comp. (355AB2) 44 735-0126 Rubber Washer 45 736-0159 Fl-Wash. .344" I.D. x .87" O.D. 20 732-0194 Spring Pin Clevis Pin .50" Dia. 46 04392 Clutch Control Lever 1 21 711-0231 47 712-0158 Hex Cent. L-Nut 5/16-18 Thd. 22 736-0119 L-Wash. 5/16" Scr.* 48 710-...

Download now

Please, enter two numbers from picture: