Votes - 2, Average rating: 4.5 ( )

Manafacture: Toro File size: 2.15 mb File name: Language of manual:

The station will shut off when the runtime counts down (or is adjusted down) to 00.0 minutes. Each station will operate in sequence for the selected runtime. Note: To terminate operation, either reduce the station runtime to 00.0 or turn the Function Selector knob momentarily to the OFF position. 63 The Run Function RUN is the Function dial position for normal controller operations. However, automatic controller operation will occur when the Function Selector knob is in any position other than OFF. 1. Turn the Function Selector knob to RUN to view the following display (example): The current date and time will be displayed on the upper line. The lower line will indicate any station number, i.e., station Station 02 in Program A, is currently operating automatically. If Station 02 was running manually the display would be shown: Note: When operation of the master valve/ pump start circuit is enabled within the Setup function, it will be energized in conjunction with any watering activity. A separate indication for master valve/pump operation is not shown on the display. The Off Function All controller output will be terminated and remain off while the function dial is in the OFF position. All other controller operations, including ET data download, will be uninterrupted. 64 Appendix A Troubleshooting Guide The landscape is too dry. 1. Turn the Function dial to ADJUST. . 2. Turn the Upper Line knob to select a station. 3. Turn Lower Line knob to adjust +5% and watch for 7 to 10 days. 4. If your landscape is still too dry, increase 5% each week until stress is eliminated. This is the optimal level. The landscape is too wet. 1. Turn the Function dial to ADJUST. 2. Turn the Upper Line knob to select a station. 3. Turn the Lower Line knob to adjust -10% and watch your landscape for 7 to 10 days. 4. If your landscape is still too wet, decrease 5% to 10% each week until you see minor stress in you landscape. 5. When you see minor stress in your landscape, increase 5% to set program at optimal level. The Alert tone continues to turn on. 1. Turn the Function dial to HELP/INFO. 2. Turn the Upper Line knob select BEEP on MESSAGE? 3. Turn the Lower Line knob to select No. 4. Turn the Function Selector knob to RUN. 65 The display is blank. 1. Power to the controller has been disconnected, either by a blown fuse or at the AC power source circuit breaker panel. Check fuse condition, referring to the procedure on page 76. Check the circuit breaker at the power source and reset as necessary. 2. If the display does not return, contact Toro Customer Support at 1-800-664-4740. The controller programs correctly but does not operate automatically. 1. Confirm the controller clock is synchronized with the current time and date. If the controller clock is wrong, watering may not occur as expected. 2. If Rain Switch is displayed, the Rain Sensor circuit has placed automatic operation on hold. If a Rain Sensor is not installed, confirm the Sensor switch is in the Bypass position. Check the Sensor wiring terminals to verify installation of a jumper wire connecting the terminals. The ADJUST Function appears to be ineffective. 1. Make sure the date and time settings are correct. 2. Turn the Function dial to REVIEW. Changes made within the Adjust function may be very subtle, resulting in minor changes to the cycle time or number of cycles, or it may be more significant depending on the percent adjustment. If it is currently Wednesday or later in the week when reviewing the schedule, the affect of the adjustment may not be evident in the Week 1 display. You should see the effect of Adjust in the Watering Day schedules of Weeks 2 - 8. 66 Week 1 of the watering day schedule appears incomplete. 1. The days prior to installation will not be shown in the Week 1 schedule. The controller shows what days have irrigated or it anticipates what days will irrigate if the weather remains as it is today. If the controller is installed on a Friday, there will be no irrigation days shown prior to Friday, which may result in no irrigation days at all for Week 1. 2. Turn the Lower Line knob to see irrigation day schedules for Week 2 - 8. The irrigation days will display a pattern as you step through the subsequent displays. The REVIEW display indicates 99+ minutes. 1. Since the displayed cycle time is limited to two digits, 99+ is shown when the total programmed cycle time is greater than 99 minutes. This display does not indicate a controller malfunction. 67 Notes 68 Appendix B Glossary of Terms Group Number - This is a code number provided by the ET Everywhere service to the Intelli-Sense controller at the time of activation. The link enables the ET Everywhere service to communicate conditions relative to controllers in locations where irrigation regulation programs are in effect. This code will only be assigned if the user is a participant in the program. High ET Start Time - In the event of a very high...

Download now

Please, enter two numbers from picture: