|
manual abstract
Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other petroleum products must not be used to clean belts. English-49 LUBRICATION Lubricating the Cables If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a cable binds, it can disrupt operation. If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to escape from the bottom. Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced. Lubricating in Accordance with the Lubrication Schedule Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out. Use only good quality bearing grease. Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality. Front Wheel Bearings Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out. Use only good quality bearing grease. Deck spindle Lower the cutting deck completely. If you use grease gun without rubber hose, the foot plate must be removed. Lubricate with a grease gun, one zerk, 2-3 strokes. Use only good quality bearing grease. IMPORTANT INFORMATION Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces. Lubricating the front wheels Deck spindle English-50 LUBRICATION Deck outer spindle Lubricate using a grease gun, one zerk, each side 23 strokes. Use only good quality bearing grease. Engine Oil Changing the Engine Oil The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it should be changed every 50 hours. WARNING! Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first. IMPORTANT INFORMATION Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location. Avoid skin contact; wash with soap and water in case of spills. 1. Place the machine on a flat surface. 2. Place a container under the engine where the hose from the oil drain valve exits. 3. Remove the dipstick and open the drain valve. 4. Allow the oil to run out into the container. 5. Then close the oil drain valve. 6. Replace the oil filter if necessary. 7. Fill with new engine oil in accordance with Checking the Oil Level. 8. Start the engine. Run it for a few seconds. Stop and re-check the oil level. Oil drain valve English-51 LUBRICATION Checking the Oil Level Check the oil level in the engine when the machine is standing level and the engine is stopped. Remove the dipstick, wipe it clean, and then replace it. The dipstick should be screwed into place. Take the dipstick out again and read the oil level. Remove the dipstick The oil level should lie between the markings on the dipstick. If the level is approaching the “ADD” mark, fill the oil to the “FULL” mark on the dipstick. Never fill to above the “FULL” mark. The oil is filled through the hole for the dipstick. API class SF, SG, SH, SJ or higher must be used. Syntetic oil SAE 5W-30 or 10W-30 is recommended at all temperatures. Mineral oil SAE 5W-30, 10W-30 can be used between -18 °C/0 °F and +5 °C/40 °F. At temperature above +5 °C/40 °F single grade SAE 30 must be used. The engine holds 0.88 qt (1.0 liters) of oil excluding the filter, including filter 2 qt (1.9 liters). English-52 LUBRICATION Changing the Engine Oil Filter 1. Drain the engine oil in accordance with the work description under the heading Engine Oil/ Change Engine Oil. 2. Remove the oil filter. If necessary, use a filter remover. 3. Wipe new, clean engine oil onto the seal for the new filter. 4. Mount the filter by hand with + 3/4 turn. 5. Run the engine warm, then check that there are no leaks around the oil filter seal. 6. Check the oil level in the engine, fill if necessary. The oil filter holds 7. 0.1 qt (0.1 liters) of oil. *Transaxle (Transmission) Fluid Change This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life an oil filter change interval of every 200 hours is recommended. The following procedure can be performed with the transaxles installed in the vehicle, and the vehicle on level ground. Apply the bypass valve for each transaxle and lock the vehicle parking brake. 1. Remove the three %" filter guard screws and filter guard. Clean any loose debris from around the perimeter of the filter. ...
Other models in this manual:Garden Tools - 36 / 968999539 (3.7 mb)
Garden Tools - 36 / 968999609 (3.7 mb)
Garden Tools - 42 / 968999689 (3.7 mb)
Garden Tools - 42 / 968999713 (3.7 mb)