Votes - 3, Average rating: 3.7 ( )

Manafacture: Classen File size: 1.1 mb File name: Language of manual:

Maximum engine rpm is recommended for smooth operation. 8. After cutting a short distance, stop machine by letting the twist grip throttle control go back to its original position. Check thickness of cut and adjust if necessary. 9. At the end of each cutting pass, lift up on the handle bar to clear the cutting blade from the sod. Retard the throttle control and turn machine around into the position for the next cut. 10. When finished cutting sod, reverse steps 6 through 3, leaving the wheel drive handle on for transportation. Under normal operating conditions, the blade angle is slight (blade bottom is flat). In extremely hard soil or when cutting with a dull blade, the blade may want to ride out of the ground. At this time, it may help to angle the blade down. A short trial run will indicate what blade angle is best. To do this, you will loosen the pitch adjustment bolt (#7 on illustration) and move it slightly toward the engine, then retighten bolt and nut. GENERAL MAINTENANCE To keep the sod cutter in good operating condition, perform the following: • Keep blade sharp; a sharp blade cuts cleaner, faster and more uniformly and places less load on the machine. Sharpen cutting edge on bevel or top side only. • Keep drive belt at proper tension and free of oil and dirt at all times. • Check engine oil level and air filter element daily. • Check for loose bolts and connections. • All grease fittings are pressurized type. Use a good grade Lithium Base Grease or equivalent. Grease eccentric arms sparingly every 4 hours of service, all others daily. Wipe off all grease fittings before and after each greasing (there are a total of 8 grease fittings). • To make sure the chain on the front drive wheels is tight, you will need to remove the chain guard to check this. If tightening is required, loosen nuts and bolts on the 3/4" pillow block bearings and push the bearings toward the back of the sod cutter until chain is tight. Make sure both bearings go back evenly to keep jackshaft running even with the frame. After doing this, retighten nuts and bolts on the bearing and replace the chain guard. • Engine (refer to Honda owner.s manual). SAFETY WARNING DO NOT STORE GASOLINE (FUEL) UNNECESSARILY OVER LONG PERIODS OF TIME. TO PREVENT POSSIBLE EXPLOSION, STORE ONLY IN AN APPROVED "SAFE" CONTAINER. TO PREVENT EXPLOSION OF VAPORIZED FUEL, DO NOT STORE MACHINE WITH FUEL IN TANK OR CARBURETOR IN AN ENCLOSURE WITH OPEN FLAME. (EXAMPLE: FURNACE OR WATER HEATER PILOT LIGHT.) TROUBLESHOOTING CHART PROBLEM CAUSE REMEDY Blade will not stay in ground a. Bottom of blade is rounded off a. Blade should be sharpened or replaced Belts jump off a. Wrong type of belt b. Pulley misalignment a. Use only the special factory belt b. Realign pulley NOTES:____________________________________________________________________________________________________ SOD CUTTER PARTS MANUAL SC-12/5.5 – S.N. 000372 & UP SC-12/8.0 – S.N. 000136 & UP SC-16/5.5 – S.N. 000104 & UP SC-18/5.5 – S.N. 003956 & UP SC-18/8.0 – S.N. 000413 & UP SC-20/5.5 – S.N. 000141 & UP SC-20/8.0 – S.N. 000164 & UP SC-24/8.0 – S.N. 000147 & UP 6 SOD CUTTER MAIN FRAME 1 C400235 1 SOD CUTTER FRAME 2 C500131 2 1/2" LOCK NUT 3 C500150 2 1/2" x 1-1/2" BOLT 4 C400232 1 SMALL GUARD 5 C400114 1 DUAL DRIVE CLUTCH ARM 6 C500101 4 5/16" NUT 7 C500115 9 5/16" LOCK WASHER 8 C500140 6 5/16" x 3/4" BOLT 9 C500146 2 3/8" x 1-1/2" BOLT 10 C500083 6 5/16" FLAT WASHER 11 C300069 1 DRIVE LINKAGE ARM 12 C100208 1 DUAL DRIVE DOUBLE IDLER PULLEY 13 C500106 1 1/2" NUT 14 C500006 1 1/2" LOCK WASHER 15 C300002 1 AXLE PIN 16 C100017 1 TIRE & WHEEL ASSEMBLY, 9x350x4 17 C500016 2 5/32" x 1-1/2" COTTER PIN 18 C400233 1 CHAIN GUARD 19 C500168 2 5/16" x 5" BOLT 20 C500041 2 3/8" LOCK NUT 21 C400234 1 LARGE GUARD 22 C500130 6 3/8" LOCK WASHER 23 C500129 8 3/8" NUT 24 C100010 2 IDLER PULLEY 25 C500042 14 3/8" FLAT WASHER 26 C500091 2 3/8" x 2" BOLT 27 C100021 2 BRASS BUSHING 28 C500001 1 GREASE FITTING, 1/4" x 28 29 C400010 1 CLUTCH ARM 30 C300134 1 L.H. BELT ADJUSTMENT CLIP 31 C500043 2 3/8" x 1" BOLT 32 C500159 1 3/8" x 3" BOLT 33 C100074 2 DECAL, "CLASSEN" 34 C100262 2 DECAL, "SC-12" 34 C100417 2 DECAL, "SC-16" 34 C100131 2 DECAL, "SC-18" 34 C100260 2 DECAL, "SC-20" 34 C100345 2 DECAL, "SC-24" 35 C100069 1 DECAL, "DANGER" 36 C100096 1 DECAL, "ALL GUARDS" 37 C100132 1 DECAL, "CUTTER BLADE" 38 C100133 1 DECAL, "SLOW/FAST" 39 C100134 1 DECAL, "WHEEL DRIVE" 40 C100106 1 DECAL, SERIAL NUMBER 41 C100073 1 LUBRICATION TAG 42 C300004 1 R.H. BELT ADJUSTMENT CLIP 43 C500154 1 3/8" x 2-1/2" BOLT 44 C400237 1 BUMPER 45 C400011 2 12" BLADE ADAPTOR 46 C500133 12 5/16" x 1" BOLT 47 C300133 2 16" BLADE ADAPTOR 48 C500142 6 5/16" x 2" BOLT 49 C300047 2 20" BLADE ADAPTOR 50 C400188 2 24" BLADE ADAPTOR 1 3 2 20 10 10 5 10 9 7 6 4 7 6 13 14 12 11 25 20 15 16 17 27 17 28 19 6 7 18 23 22 24 25 29 26 8...

Download now

Please, enter two numbers from picture: