Login:
Votes - , Average rating: ( )

User manual Agri-Fab, model PRO 125

Manafacture: Agri-Fab
File size: 667.09 kb
File name: 45-02101-101.pdf

Language of manual:en

The document is loading, please wait
The document is loading, please wait

manual abstract


SPREAD WIDTH SHIELD DOWN - 3 TO 4 FT. SPREAD WIDTH CAUTION: Read Rules for Safe Operation and Instructions Carefully PRO 125# BROADCAST SPREADER Assembly Operation Maintenance Repair Parts PRINTED IN U.S.A. FORM NO. 47438 (Rev. 2/00) TABLE OF CONTENTS SAFETY RULES...............................................................2 MAINTENANCE & STORAGE............................................9 CARTON CONTENTS......................................................2 LUBRICATION..................................................................9 ASSEMBLY ......................................................................4 PARTS EXPLOSION.......................................................10 OPERATION ....................................................................8 REPAIR PARTS..............................................................11 RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using equipment. 4. Read the product label for instructions and cautions on 1. Do not allow anyone to operate the broadcast spreader proper handling and application of lawn chemicals. without proper instructions. 5. Keep all nuts, bolts and screws tight to be sure 2. Do not permit children to operate the broadcast equipment is in safe working condition. spreader. 6. Follow maintenance and lubrication instructions as 3. Wear eye protection when handling and when apply-outlined in this manual. ing lawn chemicals. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS -- ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CARTON CONTENTS (LOOSE PARTS IN CARTON) Your broadcast spreader carton contains parts as shown in the carton contents diagram below. The hardware package contains parts shown on page 3. Identify all parts and lay out as shown. 1. Hopper Assembly 8. Hopper Screen 2. Drive Wheel 9. Handle Tube (Short) 3. Idler Wheel 10. Flow Control Arm 4. Spreader Shield 11. Handle Tube (Long) 5. Braces 12. Leg Stand Tube 6. Flow Control Rod 13. Flow Control Gauge 7. Vinyl Hopper Cover 14. Flow Control Mount Bracket 1 2 3 4 5 6 7 9 10 11 12 13 148 CARTON CONTENTS 2 FULL SIZE HARDWARE REFERENCE CHART H B C.... D.... G A.... E F I NOT SHOWN FULL SIZE J K L M N O P Q R S T U V FULL SIZE HARDWARE REFERENCE CHART H B C.... D.... G A.... E F I NOT SHOWN FULL SIZE J K L M N O P Q R S T U V REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A B C D E F G H I J K 3 2 6 2 6 16 17 5 4 1 1 Bolt, Carriage 1/4" x 3/4" Bolt, Hex 1/4" x 5/8" Bolt, Hex 1/4" x 3/4" Bolt, Hex 1/4" x 1-1/2" Bolt, Hex 1/4" x 1-3/4" Nut, Hex Lock 1/4-20 Washer, 5/16" Washer, Nylon Washer, 3/4" Cotter Pin, 3/32" x 3/4" Cotter Pin, 1/8" x 1-1/2" L MN O P Q R S T U V 1 1 4 1 2 1 1 2 1 1 2 Spacer Tube, Short (1") Spacer Tube, Long (1-5/16") Bracket, Swivel Link, Flow Control Bracket, Angle Stop Spring, Extension Knob, Hand Knob, Plastic 1/4" Grip, Control Arm Cap, Vinyl Grip, Handle 3 4 TOOLS REQUIRED FOR ASSEMBLY (1) Pliers (2) 7/16" Open End or Box Wrenches (2) 9/16" Open End or Box Wrenches ASSEMBLY INSTRUCTIONS REMOVAL OF PARTS FROM CARTON Refer to carton contents on page 2 and to the hardware chart on page 3 to lay out and identify parts and hardware needed to assemble the spreader. 5. Place the short spacer tube and a 3/4" washer onto the end of the axle that has the large drilled hole (left hand side). See figure 2. 6. Place the drive wheel onto the axle. The notched hub and the air valve should face to the outside. See figure 2. 7. Fasten the wheel to the axle using a 1/4" x 1-3/4" hex bolt and a 1/4" hex lock nut. See figure 2. REMOVE MIDDLE 3/8" BOLT, WASHER AND NUT SHAFT SUPPORT PLATE CROSSOVER TUBE FIGURE 3 FIGURE 2 8. Tip the spreader over to rest on the front edge of the hopper and on the wheels. 9. Remove the middle 3/8" hex bolt, flat washer and hex lock nut that fasten the shaft support plate to the crossover tube. Do not loosen or remove the two outer bolts. See figure 3. 1/4" x 1-3/4" HEX BOLT DRIVE WHEEL SHORT SPACER TUBE 3/4" WASHER 1/4" HEX LOCK NUT SHAFT SUPPORT PLATE FIGURE 1 3/4" WASHERS IDLER WHEEL SMALL HOLE LONG SPACER TUBE 1/8" x 1-1/2" COTTER PIN SHAFT SUPPORT PLATE ASSEMBLY OF SPREADER 1. Place the spreader upside down. 2. Assemble the long spacer tube and a 3/4" washer onto the end of axle of the axle that has the small drilled hole (right hand side). See figure 1. 3. Place the idler wheel (no notch in hub) onto the axle. The air valve should face to the outside. See figure 1. 4. Assemble one or two more 3/4" washers onto the axle and then assemble the 1/8" x 1-1/2" cotter pin. HANDLE TUBE (LONG) HEX BOLT 1/4" x 1-3/4" HEX BOLT 1/4" x 1-3/4" HANDLE BRACE SHAFT SUPPORT PLATE MIDDLE BOLT, WASHER & NUT 1/4" HEX LOCKNUT CROSSOVER TUBE FIGURE 4 HANDLE TUBE (LONG) HEX BOLT 1/4" x 1-3/4" HEX BOLT 1/4" x 1-3/4" HANDLE BRACE SHAFT SUPPORT PLATE MIDDLE BOLT, WASHER & NUT 1/4" HEX LOCKNUT CROSSOVER T...

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category