Votes - 5, Average rating: 5 ( )

Manafacture: Husqvarna File size: 1.08 mb File name: MOEN2007_V000249953.pdf Language of manual:

Now release the accelerator trigger (A) and then the throttle advance (B). WARNING: when the throttle advance is engaged, the head or blade rotates. 3) Move choke lever (E) to the closed position . 4) Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope until engine fires once. 5) Move choke lever (E) to the open position then pull starter rope until engine fires. Let engine run for a few seconds holding the trimmer. Now disengage throttle advance by pulling trigger completely. Engine will now keep on running at idle speed. HOT ENGINE STARTING STOP switch on START position I. Trigger on idle position (released). Choke towards (open position ). Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope. WARNING: when the throttle (B) advance is engaged, the head or blade rotates. 6) ENGINE STOPPING Press the stop switch moving it to STOP position 0. WARNING: when the engine is switched off rotating parts, blade or nylon string head, will keep on rotating for a few seconds. Hold the machine until all parts come to a standstill. N.B. In an emergency the above mentioned delay in stopping may be shortened by touching blade parallel on the ground. ENGLISH - 6 G. Carburetor adjustment Your machine can be equipped with a low emis- sion carbur any adjustment of the carbur ly by an authorized service center of special equipment for ensuring the best per- formance with the lowest emissions. T of technical data. speed to the minimum, turn the screw marked (T) as shown: With the engine running and well warmed up, turn the screw (T) gently clockwise, until the engine rotates at regular speed (stead noise), without the cutting devices in motion. If the cutting devices are moving, turn the screw (T) gently counterclockwise until you obtain the proper adjustment. The correct minimum speed is shown in the instruction manual in the paragraph All the above adjustments should be made with the cutting devices correctly installed. The warranty may be invalidated due to erroneous adjustments made by personnel not belonging to authorized service centers. H. Routine maintenance 1 2 3 4 7 9 10 17 H1. After every use In order to avoid overheating the motor, remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Store the machine in a dry place. After 25 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air. For more thorough cleansing, you can wash it with soapy water. After 50 hours of use Add some high speed gear grease in the gearbox through hole (C). Remove and clean the spark plug (set the space between the electrode at 0.5/0.6 mm). Replace if excessively encrusted. In case of excessive encrustation check the carburetor adjustment, the percentage of oil in the fuel mixture and make sure the oil is of excellent quality and suitable for two-stroke engines. After 100 hours of use Replace the spark plug. Every three months Contact your Service Center for a complete overhaul, replacement of the fuel filter and cleaning of the parts inside the machine. This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine. Periods of prolonged disuse See "Environmental information". If you use the machine in an exceptionally dirty or dusty environment these operations should be carried out more often. H2. Replacement of nylon string To replace the reel of string, press both the release pawls indicated by the arrows, remove the empty reel, unroll any string left and rewind the new string. Open the original package of string and insert the ends of the two strings in the eyelets on the reel, then wind the strings completely on the reel in the same direction and fasten the end of each string in the 2 opposite grooves. Replace the reel in its housing and thread the ends of the strings in their bushings. Pull each string so that about 15 cm comes out on each side. Reassemble the nylon string head as shown. If the reel becomes excessively worn, replace it with a whole new reel. H3. Attachments maintenance Follow maintenance instructions on the attachment manual. I. Techniques for use 1 4 5 6 7 8 9 speed as running it at top speed without a load can damage the engine severely. The machine is ideal to complete the work of the cutting stage, decelerate the engine to minimum lawnmover. In fact, it can reach places where a Cutting techniques engine running at high speed. After every 10 11 12 13 14 16 17 Wait until the engine is running at minimum speed before moving the machine from one section to another. ENGLISH - 7 normal lawnmower is unable to go. Cutting and trimming grass borders with the nylon string head Cutting with the nylon string head is suitable for light jobs like trimming borders and cutting the grass around trees. Mowing To prevent damage to your law...

Download now

Please, enter two numbers from picture: