Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
If someone borrows this tool, make sure they have these instructions also. ADDITIONAL RULES FOR SAFE OPERATION cont. 1. Remove the Planer from the Storage / Carrying Case and inspect it carefully to make sure that no breakage or damage has occurred during shipping. 2. Do not discard any of the packing materials until all parts are accounted for. 3. The planer has a Crescent Wrench force-fitted into the Storage / Carrying Case. 4. The Edge Guide is force-fitted into the top of the lid of the Storage / Carrying Case. 5. Also included with your planer and force fitted into the Storage / Carrying Case is a Rabbet Guide. 6. Two blades are included with your planer. 7. If any of the parts are damaged or missing (refer to PARTS LIST below), return the planer to your nearest Sears store or Craftsman outlet to have the planer replaced. UNPACKING PARTS LIST WARNING: If any parts are missing, DO NOT operate this planer until the missing parts are replaced. Failure to do so could result in possible serious personal injury. ! 8. Operator’s Manual 3. Rabbet Guide 2. Edge Guide 4. Wrench 5. Two Blades 1. Planer Inches mm 0 0 10 20 1 112 0 1/64 1/32 3 / 6 4 7. Storage / Carrying Case 6. Two Screws 10 DESCRIPTION Your planer has a precision-built electric motor and it should be connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current). DO NOT operate on direct current (DC). The large voltage drop will cause a loss of power and the motor will overheat. If the planer does not operate when plugged into correct 120-volt, 60-Hz AC ONLY outlet, check the power supply. This planer has a 10-ft., 2-wire power cord (no adapter needed). KNOW YOUR PLANER NOTE: Before attempting to use your planer, familiarize yourself with all of the operating features and safety requirements. This Professional Planer has the following features: 1. Powerful, heavy-duty 7-Amp motor provides high speed needed for fast, clean cuts in most any type of wood. Precision balanced for smooth, quiet operation. 2. Low profile depth-of-cut control knob allows easy depth-of-cut adjustments from 0 to 1/8-in. 3. Grooved front shoe design for 45° bevel or chamfer cuts. 4. Ergonomically designed contoured top-mount handle and front assist handle with soft grips for positive gripping, balance, control and comfort. 5. Heavy-duty extended length trigger switch conveniently located for comfort and control. Lock-off button helps prevent accidental starts. 6. 31/4-inch cutting width for fast planing. Planes wide side of 2 X 4 board in one pass. 7. Uses reversible, double-edged hardened steel carbide-tipped blades that can be used on both sides for longer blade life. 8. Includes edge guide for accurate, precise cuts on long or uneven workpieces. 9. Includes rabbet guide for making 15/16-in. deep rabbet cuts. 10. Chip chute keeps work surface clean and directs wood chips away from operator. 11. Permanently lubricated bearings for smooth, efficient operation and long life. 12. Cogged timing belt drive provides positive, precise power transmission. 13. High-impact plastic motor housing and handles help protect tool from damage and reduce weight. 14. Includes high-impact resistant storage / carrying case. 11 DESCRIPTION cont. This Professional Planer has the following features: Fig. 1 Depth Adjustment Knob Left or Right Dust/ Chip Extraction Trigger Switch PRODUCT SPECIFICATIONS Input Cutting Width Cutting Depth Max. Rabbet Cut Rating No-Load Speed 7 Amps 3 1/4 in. 0 to 1/8-in. 15/16-in. 120 volts, 60 Hz AC 12,000 RPM Rear Handle Front Handle On/Off Button 0 1/64 1/32 3 / 6 4 Base plate stand 12 OPERATION PREPARING FOR OPERATION Your planer has a rear handle and front assist handle for ease of operation. They provide the two-hand operation which is necessary to maintain proper control of the planer. ALWAYS keep both hands clear of the blades and the cutting area. ALWAYS use both hands when using the planer. Hold the front handle with your left hand and the rear handle with your right hand (as shown in Fig, 2). This position makes your planer easier to handle and keeps you clear of the chip exhaust. WARNING: Your planer should NEVER be connected to power supply when you are assembling parts, making adjustments, changing belts or blades, cleaning planer, or when not in use. Disconnecting planer will prevent accidental starting that could cause serious injury. ! CAUTION: DO NOT plane too fast because this causes build up in the chip exhaust. Chip build-up restricts air flow and can cause the motor to over heat. ! DANGER: If the cord hangs up on the work during the cut, release the trigger switch immediately. Unplug the planer and check the cord for damage. If there is no damage, reposition the cord to prevent it from hanging up again. If the cord has been damaged, have it replaced before using your planer. ! WARNING: Using your planer with a damaged cord could cause electrical shock resulting in serious injury. ! Keep the cord away from the cutting area. ALWAYS ...