Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
4. There must not be objects, such as utility lines, nearby that will present a hazard while working. general Operating instructions dEPth KnOB (48) FrOnt BaSE rEar BaSE PlatE (54) PlatE (61) 1. While standing to the side of the wood stock, hold the Planer firmly with one hand on the handle portion of the Housing (15, 45), and the other hand on the Depth Knob (48). 2. Set the Front Base Plate (54) of the Planer on the front edge of the wood stock. Then, depress the Safety Lock Button (17) and squeeze the Trigger (16) to start the Planer. iMPOrtant: Do not allow the Blades (57) of the Planer to contact the wood stock until the Blades are spinning at full speed. 3. While placing pressure on the Front Base Plate (54) to control the depth of cut, and while placing pressure on the Guide (64) against the wood stock to control the width of cut, feed the Planer slowly until the Rear Base Plate (61) contacts the wood stock. Then, transfer pressure to the Rear Base Plate, and SKU 91062 For technical questions, please call 1-800-444-3353. Page 9 continue planing slowly to the end of the cut. Do not pull the Planer back over the surface already cut. 4. If necessary, repeat Step #5, using progressively deeper cuts until you near the desired depth. Then, readjust the Depth Knob (48) to make a light cut for the final pass. nOtE: The Planer’s Motor may stall if the tool is improperly used. If the Motor begins to stall, reduce the feed speed at which you are making the cut and/or reduce the depth of the cut. 5. When finished planing, release pressure on the Trigger (16) and the Planer will automatically stop. Wait until Planer blade comes to a complete stop. 6. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. Page 10 For technical questions, please call 1-800-444-3353. SKU 91062 MaintEnancE and SErVicing Procedures not specifically explained in this manual must be performed only by a qualified technician. tO PrEVEnt SEriOuS injurY FrOM accidEntal OPEratiOn: turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. tO PrEVEnt SEriOuS injurY FrOM tOOl FailurE: do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use. cleaning, Maintenance, and lubrication 1. BEFOrE Each uSE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. to clean the outer body of the Planer, use a shop vacuum or compressed air. Do not immerse any part of this Planer in liquid. 3. to replace the Motor carbon Brushes: It may become necessary at sometime to replace or clean the two Carbon Brushes (36) when the Motor performance decreases, or stops working completely. The Carbon Brushes are located on the side of the Right Motor Housing (45). To do so: a. Remove the two Carbon Brush Caps (35). b. Then, remove the two Carbon Brushes from the Brush Holders (38). c. If a Carbon Brush is worn down more than 1/2 of its original length, replace both Carbon Brushes. If, however, the Carbon Brushes are just dirty they may be cleaned by rubbing them with a pencil eraser. d. When installing the Carbon Brushes, make sure the carbon portion of the Carbon Brushes contact the Motor Armature, and that the springs face away from the Motor. Also, make sure the springs operate freely. e. After cleaning or replacement, replace the Carbon Brush Caps with a screwdriver and tighten firmly. cautiOn! Use caution as blades are very sharp. Warning! Only straight blades can be used with this planer. 4. to reverse or replace the Blades: The Planer is equipped with two reversible Blades (57). Do not attempt to sharpen the Blades. Always reverse or replace the Blades as a set in order to avoid an imbalance of the Blade Holder (59). To reverse or replace the Blades: SKU 91062 For technical questions, please call 1-800-444-3353. Page 11 (BOttOM ViEW) hEX hEad ScrEW (60) a. Loosen the three Hex Head Screws (60) that secure the Blades, Press Blade Plate (56), and Blade Holder to the Blade Shaft (63). b. Slide the Blades lengthwise out of the Blade Shaft, using a piece of wood to avoid cuts to your fingers. BladE (57) hEX hEad ScrEW (60) BladE hOldEr (59) PrESS BladE PlatE (56) BladE ShaFt (63) c. Once the Blades have been removed, clean the Blades, Press Blade Plate, Blade Holder, and the Blade Shaft thoroughly before installing the reversed or new Blades to allow for a more accurate Blade setting. d. When installing the reversed or new Blades, it is important that they be properly adjusted so that they align evenly with the Front Base Plate (54) and Rear Base Plate (61). Slide the Blades lengthwise into the Blade Shaft, using a piece of wood. align BladES uSing PiEcE OF WOOd...