Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 15   File size: 14 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

This warranty gives you specific legal rights. Your may also have other rights which vary from State to State. Some States do not allow the exclusion or limitation of incidental or consequential damages and the foregoing exclusions may not apply to you. No agent, representative, dealer or employee of B&K has the authority to increase or alter the obligations or terms of this warranty. Returning Equipment NoequipmentmaybereturnedtoB&K ComponentsLtd. withoutaRETURNAUTHORIZATION(RA). Shouldyoufindi

downloaded: 1   File size: 8 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

Any IR data received from the keypad control terminals will be sent to all 9 IR outputs. Off - All 9 IR outputs will be turned off. Front Panel IR to Flasher Outputs: If Front Panel IR to Flasher Outputs is set to YES, any IR received by the front panel will pass through the CT Receiver to the flasher outputs. Otherwise when set to NO, IR commands received will only stay internal to the unit. Regardless of this setting B&K will always respond to its own IR commands. The default is set to NO beca

downloaded: 3   File size: 8 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

CTRL OUT - The 12VDC 200mA outputs are used to control external amplifiers, relays, screens or devices that activate when a voltage is detected. The default action is that the voltage is ON when the Zone is ON, OFF when the zone is off. This is controlled by going into the Advanced FULL Setup Tab 9 in BKcSuite. The 12VDC controls can be modified to the following choices: Zone On -The 12V Control Out is on if the corresponding Zone is on (This is Default). Zone Active - The 12V Control Out will t

downloaded: 43   File size: 8 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

All rights reserved. The information in this manual is copyright protected. No part of this manual may be copied or reproduced in any form without prior written consent from B & K Components, Ltd. B & K Components, Ltd. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior notice. The information in this manual may be subject to change without prior notice. ***Warning - PC requiremen

downloaded: 7   File size: 8 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

Use Left/Right to select a zone to setup for power on settings. Then use up/down to select an item to adjust. Use Left/Right to adjust the item selected. 2. When the selected zone is powered on, how do you want the zone to come up? This is where you can select turn on input, turn on volume, turn on bass, treble, loudness, etc. Every time you turn on this zone it will “Power On” to specific predetermined setting. Last used will allow the zone to turn on exactly how it was turned off, i.e. input,

downloaded: 4   File size: 8 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

Any of these products can be combined to share sources in a CT system. Depending on which form of control communication you wish to use (IR or RS-232), B&K can accommodate either or both. Typically only one form of communication is needed, however for some advanced installations, both forms may be required. The following diagrams depicts both IR or RS-232 being used to control the home theater product. The CT-1 allows an easy method to interface between a home theater and a whole house distribut

downloaded: 1   File size: 6 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

To configure the V1 output see page 33. ZB / V2 Out - The V2 output can be configured as an output for a second recording device in Zone B or as a Zone B line output to connect a second video monitor and/or audio amplifier. As a record output, V2 will output the analog audio and video from the selected input in Zone B except when V2 is selected. This prevents feedback through the recording device which could damage your speakers. As a line output V2 will output the analog audio and video from wh

downloaded: 1   File size: 6 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

Plug one RJ- 45 end into the main RJ-45 jack on the back panel of the receiver. Plug the other end into the RJ-45 jack labeled Master IN on the back of the keypad. The main RJ-45 jack on the receiver will supply connections for +12VDC power @ 200mA, IR data and +12V control @ 50mA. See page 36 for the main RJ-45 pin out description. A keypad can be configured to control connected sources with IR by setting the control outputs to REMOTE. See the control output configuration page 34. A CK1.2 keypa

downloaded: 2   File size: 6 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

From the front panel press Menu repeatedly until you leave the menu system UP/DOWN ARROWS -Once you are in the menu system, use the UP/DOWN ARROWS to move to the desired menu selection. With the supplied SR10.1 remote, rocking the thumb pad forward and backwards act as the up and down arrows.The current active menu line is highlighted in a contrasting color in the On-screen display and also shown on the front panel display. SELECT / ENTER -Some menu selections select another menu level to be act

downloaded: 32   File size: 6 mb   Manafacture: B&K  
Category: Receivers & Amplifiers
@name

You may repeat the following steps for each input by changing inputs on the top line of the menu or with the supplied remote control. 1. Default Audio Modes -There are two major categories of audio, 2-channel and 5.1 multi-channel. Two channel audio might come from an analog VCR, a PCM CD or a Dolby Digital 2.0 DVD. The first three selections in this menu for Default Mode, Default Speakers and 2-chan Decoder apply only to 2-channel audio. The Default Mode defines the listening mode the receiver





Category