Each band is adjusted by a center detented fader with ± 12dB of gain available, and a master fader controls system gain for that channel. Clip and signal present LEDs, as well as a bypass switch, are also provided on each channel. Inputs and outputs for each channel are via both 1/4" and RCA jacks. The unit can also be rack mounted in only 1 rack space. FEATURES • 2 complete 30 band 1/3 octave equalizers in 1 rack space • Power up delay circuitry protects speakers by eliminating turn-on transien

About Alesis Matica. Amplifiers Thank you for purchasing an Alesis Matica power amplifier, one of the most advanced and highest value amplifiers available. Your Alesis High Speed, Wide Bandwidth amplifier provides extremely accurate sonic quality as well as measured specifications, but its conservative design and careful attention to electronic protection means that it will continue to operate at top condition without special attention, year after year. Matica amplifiers use the newest generatio

See below for output wiring in Bridged Mono configuration. Audio Installation: Output Wiring Warning: Be sure that the AC power is off prior to connecting or disconnecting any signal wiring. Alesis amplifiers can reliably drive 2 W loads in Stereo mode and 4 W loads in Bridged Mono mode. However, the impedance of a loudspeaker varies with frequency, and its nominal rated impedance is not necessarily its minimum impedance. Some loudspeakers carry both nominal and minimum impedance specifications,

Since 1984, we've been designing and building creative tools for the audio community. We believe in our products, because we've heard the results that creative people like you have achieved with them. One of Alesis' goals is to make high-quality studio equipment available to everyone, and this Reference Manual is an important part of that. After all, there's no point in making equipment with all kinds of capabilities if no one explains how to use them. So, we try to write our manuals as carefull

How To Use This Manual This manual is divided into the following sections describing the various modes of the NanoVerb. Though we recommend you take time to read through the entire manual once carefully, those having general knowledge about effects devices should use the table of contents to reference specific functions. Chapter 1: Your First Session with the NanoVerb. A basic introduction on operating the NanoVerb, auditioning the factory programs, and adjusting levels. Chapter 2: Connections.

4. Stellen Sie den Equaliser an einen fur den Betrieb geeigneten Platz. 5. Stellen Sie sicher, da. alle Gerate ausgeschaltet sind und alle Lautstarkenregler auf “null“ gestellt sind. 6. Schliessen Sie alle Eingabequellen wie im Diagramm gezeigt an. 7. Schliessen Sie die Ausgange an den (die) Verstarker, Cassettendecks und/oder Audioquellen an. 8. Schliessen Sie Ihren Equaliser und andere Gerate an die Wechselstromversorgung an. 9. Schalten Sie alle Gerate in der folgenden Reihenfolge ein: • Audi

For a more detailed explanation of the Release Edit Group function, see pages 44 and 45. Remember, if you want to keep the edited program, be sure to store it to one of the User locations. For instructions on how to do this, turn to page 38. 3 3 Basics of Equalization Basic operation: Store mode Once you have created a program you would like to save, press the [STORE] button to enter Store mode. This will cause the Numeric LED Display to blink with the number of the current program. If you were

5 Important Safety Instructions..................................7 Important Safety Instructions (English)...................................7 Safety symbols used in this product.........................................................7 Please follow these precautions when using this product: ...................7 Instructions de Securite Importantes (French) ...................... 9 Symboles utilises dans ce produit.............................................................9 Veuillez suivre ce

This value is not stored with a program. HEADPHONES Jack Plug your headphones into this jack using a standard 1/4” stereo phone plug. If your headphones are 1/8”, you can find a 1/8” to 1/4” adapter in most electronics stores. The internal speaker, STEREO LINK OUTPUT and SPEAKER OUTPUT are automatically disabled when you are using headphones. Power Switch Use this switch to turn the Wildfire on and off. A program’s BASS and TREBLE values will be lost if you switchprograms without saving that pro

Make sure all items listed on the front of this guide are in the Spitfire's box. 2. Read the Important Safety Instructions document included with the Spitfire. 3. Study the Hookup Diagram below. 4. Make sure all equipment is turned off and all gain knobs are set to zero. 5. Connect your guitar and other equipment to the Spitfire in the manner illustrated below. Refer to the Features section for details on which cables and equipment to use. 6. Plug in all devices and turn them on. 7. Experiment w