Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
Expansion Port IN: from Tango Audio Controller Expansion Port OUT: FIG. 1 Tango Zone Expanders (DAS-T0808X-SIG shown) Address Switch Zone Outputs (up to 8) Paging IN/OUT Stereo Inputs/Outputs (8) Power Switch & Receptacle to other Expander or other Expander • Each Zone Expander has the capability of offering 4 or 8 zones per Expander. • Up to 7 Zone Expanders may be used in the system, offering the ability to expand the system to 64 zones. Product Specifications Tango Zone Expanders Product Specifications Models Available: • DAS-T0804X-SIG (FG1103-11) Tango 4-Zone Expander • DAS-T0808X-SIG (FG1103-12) Tango 8-Zone Expander Stereo Output: 40 Watts/CH Stereo amplifiers (20Hz - 20 KHz @ .1% THD) Power: 960W max (Actual average usage = 300W) Audio Inputs: 8 Stereo Inputs, 47K impedance Audio Outputs: 8 Stereo Looping Outputs Zones: 4 or 8 Independent Zones (4 X 2 Zone Modules). Front Panel Components: Light Bar Blue light bar indicates power status. LEDs Blue LEDs indicate active zones. Rear Panel Components: • Power Switch/ Receptacle Master power switch remains in ON position normally • Paging In/Out Ports RCA jacks to connect to Paging devices (any audio input can be used as a paging device). The Paging device connects to the Controller via the "Paging In" connector. The “Paging Out” connector is used to carry the page to Zone Expander(s). • Expansion IN Port RJ11 - From Mi Series Controller or other Zone Expander • Expansion OUT Port RJ11 - To another Zone Expander • Address Switch Sets the address of the Zone Expander and the zones within that Expander • Zone Outputs Connections for up to 8 zone outputs that connect to the keypads Dimensions (HWD): 17” x 3.5” x 13.5” (43.18cm x 8.89cm x 34.29cm) (including feet and connectors) Weight: 8 27.95 lbs. (12.68 kg) Included Accessories: • Power cable Other AMX Equipment: • Rack-Mount Installation Kit (FG1101-60) Tango units occupy two rack spaces in a standard 19" equipment rack. Rack mounting brackets are supplied with the optional Rack-Mount Installation Kit (FG1101-60). Note: Exercise extreme care when lifting or moving Tango units within the rack to avoid injury. It is recommended that you seek the assistance of another person when rack mounting Tango units. 1. Attach the rack mounting brackets to each side of the Tango unit using the four screws (10-32 Panhead Phillips - supplied with the Tango unit) for each bracket. Note: To prevent injury the Tango unit must be securely attached to the rack in accordance with the installation instructions. ALWAYS use the special rack mount brackets supplied and high quality fixing screws to ensure the Tango unit is installed in the rack correctly. 2. Place the Tango unit in the equipment rack and hold steady. 3. Secure the Tango unit in the rack using the mounting holes. Note: DO NOT stand other units directly on top of the Tango unit when it is rack mounted, as this will place excessive strain on the mounting brackets. Ventilation To ensure that the rack enclosure is adequately ventilated, there must be a minimum of 3" all around the Tango unit. Sufficient airflow must be achieved (by convection or forced-air cooling) to satisfy the ventilation requirements of all the items of equipment installed within the rack. Speaker Wire Technology (SWT) Speaker Wire Technology (SWT) allows both data and audio signals to travel over the same four conductor wire. This remarkable technology removes the need for control wire since the control and audio signals are shared on the same wire. The reliability and simplicity of this system has been proven for years. AMX Distributed Audio is the only company that offers a “retrofit solution”, one which allows the replacement of volume controls with AMX Distributed Audio keypads and Controllers, giving full control over the sources. Additionally, the versatility of SWT also allows AMX Distributed Audio products to be connected where the control wire has been run separately from the speaker cable. Cabling Instructions CAUTION: Be sure to check for any wiring restrictions required by the electrical code in your area. This installation uses low voltage cabling similar to telephone and alarm wiring, and as such does not commonly have very many restrictions on their installation. However rules may vary in different regions. Cable Type The Tango Controller is cabled using standard 4-conductor speaker cable originating at the Tango Controller, passing through the Keypad, and terminating at the speaker location. AMX recommends using a bundled 4-conductor 16- gauge stranded copper wire in a single continuous run. Connecting Sources (Audio Inputs/Outputs) Up to 8 audio devices can be connected to the Tango Zone Expanders via the Sources INPUT and OUTPUT RCA connectors on the rear panel (see FIG. 1 on page 1). Industry standard RCA connectors provide line-level input and output connections for devices such as CD, DSS, MP3 players etc. Each audio input has a corresponding buffered output used to connect t...