Votes - 2, Average rating: 4.5 ( )

Manafacture: Kenwood File size: 729.65 kb File name: Language of manual:

Other manuals for this model:

Receivers & Amplifiers - KRF-V7020 (729.73 kb)

Remote Control - KRF-V7020 (178.36 kb)

• To return to the original indication, repeat the above procedure. • You also will need to change the name input to the remote control (RC-0508) to “MD”. RC3 Selecting the speaker system Press the SPEAKERS A or B key to select the speaker system to be used. A ON B ON A+B ON : Sound from the speakers connected to the SPEAKERS A terminals on the rear panel. : Sound from the speakers connected to the SPEAKERS B terminals on the rear panel. : Sound from both the speakers connected to the SPEAKERS A and B terminals on the rear panel. A+B OFF : No sound from the speakers. Use this setting when listening with headphones for stereo sound in all playback modes. • Activating a surround mode or selecting “DVD 6ch” as the input source causes speaker system A to be selected automatically. On the KRF-V5020, press the SPEAKERS key to switch the speakers on and off. The indicator for the speakers you want to use should be lit. Speaker indicator lights. ASP SW RLB SP SW RL Models other than KRF-V5020 KRF-V5020 Selecting VIDEO 2/MONITOR Depending on the component connected to the VIDEO 2/MONITOR jacks, select either the “VIDEO 2” setting or the “MONITOR” setting, as appropriate. 8 Normal playback KRF-V7020/V6020/V5020 (En/T) Listening to a source component VOLUME CONTROL Adjusting the sound SOURCE DIRECT VOLUME CONTROL 15 INPUT SELECTOR SOUND MULTI CONTROL BASS BOOST PHONES VIDEO AUDIO VOLUME VOLUME Input selector keys RC-R0508 RC-R0710 1 Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)) to select the source you want to listen to. The input sources change as shown below: Selecting a source using the INPUT SELECTOR knob 1 TUNER 2 "CD" ("CD"*) 3 "TAPE" or "MD" ("TAPE"*) 4 "PHONO"("PHONO"*) 5 "VIDEO1" ("VCR1"*) 6 "VIDEO2" ("VCR2"*) 7 "DVD 6ch" Selecting a source using the AUDIO key on the remote control (RC-R0508) 1 "CD" ("CD"*) 2 "TAPE" or "MD" ("TAPE"*) 3 TUNER 4 "PHONO"("PHONO"*) Selecting a source using the VIDEO key on the remote control (RC-R0508) 1 "VIDEO1" ("VCR1"*) 2 "VIDEO2" ("VCR2"*) 3 "DVD 6ch" • When selecting an input source by using the remote control (RCR0710), press the desired input selector key. • “VIDEO 2” can be selected as an input source only if the VIDEO 2/ MONITOR setting is “VIDEO 2”. 8 * Once setup codes are registered in the remote control (RC-R0508), the input name display changes according to the name of the registered component. Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears instead of "VIDEO 1". RC2 • When using the remote control (RC-R0508) after initial setup, any inputs that have not been registered with a setup code are deleted from the cyclic list. RC4 • The INPUT SELECTOR on the front panel of the receiver always cycles through all inputs. 2Start playback from the selected source. SPEAKERS A/B SPEAKERS, MUTE (KRF-V5020) VIDEO VOLUME VOLUME MUTE TUNING/SKIP SOUND MUTE MULTI CONTROL SOUND RC-R0508 RC-R0710 Adjusting the tone The following adjustments are possible if the receiver is in the stereo mode. 1 Press the SOUND key to select the tone mode to be adjusted. BASS: Select this to adjust the low frequency range. (Press the SOUND key once.) TREB: Select this to adjust the high frequency range. (Press the SOUND key twice.) SP A RL SW STEREO TREB +4 2 Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound quality. • The bass and treble levels are adjustable from -10 to +10 in 2 step increments. • The adjustment item is displayed for approximately 8 seconds. • If you used the remote control (RC-R0508) to perform the above setting, press the VIDEO key at this point to turn off the remote control’s own adjustment mode. In this case, the input source is not switched. Once-touch low frequency emphasis (bass boost) The following adjustments are possible if the receiver is in the stereo mode. Press the BASS BOOST key. • Press the key once to select the maximum (+10) low frequency emphasis setting. • This key does not function when the receiver is in the sound quality or ambience effects mode. Switching back to the previous setting Press the BASS BOOST key again. Operations 3Use the VOLUME CONTROL (VOLUME) to adjust the volume. Normal playback Recording KRF-V7020/V6020/V5020 (En/T) Recording audio VIDEO 2 / MONITOR Muting the sound MUTE lets you mute the sound of the speakers. Press the MUTE key. SP MUTE A RL SW CD INPUT SELECTOR Operations TAPE = MONITOR copying Blinks • On the KRF-V5020, this selection can be made using the control on the receiver as well. To cancel Press the MUTE key again so that the “MUTE” indicator goes off. • Muting can also be cancelled by adjusting the volume. SOURCE DIRECT playback (analog sources only) Use this function to pass the source material direct to the amplifier, bypassing any audio processing. Press the SOURCE DIRECT key. S.DIRECT • Either press the LISTEN MODE, SOUND, and SETUP keys, or switch to another input source to cancel SOURCE DIRECT playback. To cancel Press again. • If SOURCE DIRECT playback was activated when using a surround ...

Download now

Please, enter two numbers from picture: