Votes - 3, Average rating: 3
(
)
)
|
manual abstract
1 1 ...................... 2 2 ...................... 4 3 ...................... 4 4 ...................... 1 5 ...................... 5 6 ...................... 1 7 ...................... 1 8 External view Number of items + - KENWOOD disc changer control input • To connect the Disc changer, consult your Disc changer manual. • Be always sure to connect the Disc changer to the "To DISC CHANGER" terminal of the DAB hideaway unit. Do not connect it to a connection terminal of the Main unit. NOTE Fuse (3A) DAB connection cable (Accessory1) Battery DAB antenna cable DAB antenna (Accessory7) Battery cable (Commercially available) Ground cable (Commercially available) Power terminal Pass battery and ground cables through supplied terminal cover and connect to respective terminals. After completing connections, fasten terminal cover5 over terminal bracket. Terminal cover (Accessory5) Lead terminal (Commercially available) DAB hideaway tuner control input Control unit DAB hideaway tuner DC voltage is output from the DAB antenna terminal of the DAB hideaway tuner to supply power to the DAB antenna. Be sure to connect the supplied DAB antenna only. Otherwise, the unit may be damaged. 2CAUTION Disc changer To control unit NOTE The use of any accessories except for those provided might result sure only to use the accessories shipped with the unit, as shown Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the terminal of the battery. 2. Install the DAB antenna and connect the antenna cable to the DAB hideaway tuner. 3. Connect the DAB hideaway tuner and the control unit using the provided DAB connection cable. 4. Make the proper input and output cable connections for each unit. 5. Connect the battery cable and ground cable to the DAB hideaway tuner. 6. Install the unit in your car. 7. Reconnect the - terminal of the battery. 8. Press the reset button. CAUTION • Do not connect the DAB control cable whilst the control unit is turned ON. • Be sure to press the reset button after installation. • If your car is not prepared for this special connection-system, consult your kenwood dealer. • Make sure that all cable connections are securely made by inserting jacks until they lock completely. • If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits, also do not remove the caps on the ends of the unconnected cables or the terminals. • Some disc changers need conversion cables for connection. See the section on "Safety Precautions" for details. • Insulate unconnected cables with vinyl tape or other similar material. • Be sure to use the provided DAB antenna (Accessory 7) as the DAB antenna. Using other antenna than provide may lead to malfunction. • Take care so that the antenna cable and other connection cables are not caught by mobile parts. Otherwise cable disconnection or other trouble may result. • Do not apply too much force on the antenna cable, other connection cables and connectors by bending a cable, etc. Otherwise cable disconnection or other trouble may result. • Securely fasten the screws that fix the DAB antenna as well as the screws of the DAB antenna itself. Screws that loosen introduce the danger of the antenna coming apart during travel. • DC voltage is output from the DAB antenna terminal of the DAB hideaway tuner to supply power to the DAB antenna. Be sure to connect the supplied DAB antenna only. Otherwise, the unit may be damaged. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. 21 What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION No sound can be heard, or the volume is low. Nothing happens when the buttons are pressed. The computer chip in the unit is not functioning normally. Press the reset button on the Control unit . The fuse has blown. After checking for short circuits in the cables, replace the fuse with one having the same rating. The input/output cables or wiring harness are connected incorrectly. Reconnect the input/output cables and/or the wiring harness correctly. See the section on "Connecting Cables to Terminals". Troubleshooting Guide The DAB mode cannot be selected. The DAB connection cable is not connected. Use the DAB connection cable to connect the control unit and the DAB hideaway tuner. Connect the power supply of the DAB hideaway tuner. Connect the battery cable and ground cable to the DAB hideaway tuner. The unit is connected to the CD changer. Connect directly to the control unit. The frequency is displayed, but no sound can be heard. The DAB antenna is not connected. Connect it ...