Votes - 5, Average rating: 3.4
(
)
)
|
Other manuals for this model:
manual abstract
Press again to restore the sound output to the previous volume level (see page 19). © CD/TAPE switch Switches the function of the control buttons numbered © between controlling YAMAHA CD players and controlling YAMAHA cassette tape deck when the AMP/DEVICE switch is slid to the DEVICE position. + u PRESET d A/B/C/D/E MUTE A/B e DIR A DIR B REC 7 CONTROLS AND FUNCTIONS Installing batteries in the remote control ■ Notes on batteries • Change all of the batteries if the operation range of the remote control decreases. •Use AAA, R03, UM-4 batteries for the remote control. • Make sure that the polarities are correct. See the illustration inside the battery compartment of each remote control. • Remove the batteries if the remote control is not used for an extended period of time. • Do not use old batteries together with new ones. • Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. • We strongly recommend using alkaline batteries. • If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. • Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations. 1 Open the battery compartment cover. 2 Insert the supplied batteries in each remote control according to the polarity markings (+ and -) on the inside of the battery compartment. 3 Close the cover back. Using the remote control The remote control transmit a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit. ■ Handling the remote control • The area between the remote control and this unit must be clear of large obstacles. • Do not spill water or other liquids on the remote control. • Do not drop the remote control. • Do not leave or store the remote control in the following types of conditions: -places of high humidity, such as near a bath -places of high temperature, such as near a heater or a stove - places of extremely low temperatures - dusty places • Do not expose the remote control sensor to strong lighting, in particular, an inverter type fluorescent lamp; otherwise, the remote control may not work properly. If necessary, position this unit away from direct lighting. 8 CONNECTIONS CAUTION • Do not connect this unit or other components to the main power until all connections between components are complete. • Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/ or the speakers. • All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “-” to “-”. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also, refer to the owner’s manual for each of your components. • Use the RCA type pin plug cables for audio components except speakers. y • The PHONO jacks are designed to connect a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-output MC cartridge, use an in-line boosting transformer or an MC-head amplifier when connecting your turntable to the PHONO jacks. • Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to the GND terminal for some record players. MP3 player, etc. CD/DVD player, etc. MD recorder, etc. 9 CONNECTIONS Connecting speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “-” (black) properly. CAUTION Before connecting the speakers, make sure that the power of this unit is off. _ ■ Connecting the banana plug (U.S.A., Canada, Australia and General models only) First, tighten the knob and then insert the banana plug into the end of the corresponding terminal. 1 Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable and twist the exposed wires of the cable together to prevent short circuits. 10 mm (S/B in) Banana plug 2 Unscrew the knob. Red: positive (+) Black: negative (-) Notes • One or two speaker sets can be connected to this unit. If you use only one speaker set, connect it to either the SPEAKERS A or B terminals. • Use speakers with the specified impedance shown on the rear panel of this unit. ■ IMPEDANCE SELECTOR switch 3 Insert one bare wire into the hole in the side of each terminal. Red: positive (+) Black: negative (-) CAUTION Do not slide the IMPEDANCE SELECTOR switch while the power of this unit is turned on, as doing so may damage the unit. Select the switch position (left or right) according to the impedance of the speakers ...