|
manual abstract
* In the same way, program other stations to A2, A3 ... A8. * You can program more stations to preset station numbers on other groups in the same way by selecting other groups in step 2. 1 Select the group of preset stations. 2 Select the preset station number. Notes • A new setting can be programmed in place of the former one. • For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the POWER switch is set off or the power plug is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the PRESET TUNING steps. MAN’L/AUTO FM MEMORY MEMO A/B/C/D/E A/B/C/D/E Flashes on and off for about 5 seconds. Shows the displayed station has been programmed to A1. MHz AUTO ST 1 5 2 6 3 7 4 8 PRESET STATIONS 1 5 2 6 3 7 4 8 PRESET STATIONS English English You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 10. TX-492RDS only * Only RDS stations can be stored by this function. * Refer to page 13–17 for details on RDS stations. * Parts in shaded area ( ) are present on TX-492RDS only. To store stations 1 FM/MW/LW TX-492RDS FM/AM TX-492 2 The automatic preset tuning begins from the frequency currently displayed. Received stations are programmed to A1, A2 ... A8 sequentially. * If more than 8 stations are received, they are also programmed to the preset station numbers on other groups (B, C, D and E) in that order. Press and hold for about 3 seconds. Flashes. MAN’L/AUTO FM MEMORY MHz AUTO ST MEMO 21 When the automatic preset tuning is finished The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section “To recall a preset station” on page 10. To recall a preset station Simply follow the procedure of the section “To recall a preset station” on page 10. * A recalled station is shown by the frequency or station name TX-492RDS only on the display. Notes . If no station is received by the automatic preset tuning search, the search finishes after “NOTHING” flashes for about 3 seconds on the display. TX-492RDS only . You can replace a preset station by another FM, MW or LW station manually by simply following the procedure of the section “To store stations” on page 10. . The automatic preset tuning search will be performed through all RDS network frequencies until stations are stored up to E8. If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching all frequencies. . With this function, only RDS stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune in to it with the MANUAL TUNING method (in monaural) and program it by following the procedure of the section “To store stations” on page 10. * There may be a case that this function cannot receive a station which could be received by the automatic tuning method. This is because this function receives a large volume of PI (Program Identification) data along with the station. TX-492 only . You can replace a preset station by another FM or AM station manually by simply following the procedure of the section “To store stations” on page 10. . The automatic preset tuning search will be performed through all FM frequencies until stations are stored up to E8. If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching all frequencies. . With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune in to it with the MANUAL TUNING method (in monaural) and program it by following the procedure of the section “To store stations” on page 10. EXCHANGING PRESET STATIONS EXCHANGING PRESET STATIONS * Parts in shaded area ( ) are present on 2, 4 TX-492RDS only. Example) If you want to shift the preset station on E1 to A5, and vice versa. 1 Recall the preset station on E1 (by following the method of “To recall a preset station” on page 10). 2 Flashes. ED IT MHz ST EDIT 3 Next, recall the preset station on A5 by following the same method with step 1. Flashes. MHz ST EDIT 4 Shows the exchange of stations is completed. Lights up for a moment. EDIT ED IT In areas where RDS broadcasts cannot be received, the RDS broadcast functions do not operate. (The procedures from page 13 to page 17 are not necessary.) In areas where RDS broadcasts cannot be received, the RD...
Other models in this manual:Receivers & Amplifiers - TX-492RDS (1.28 mb)