Votes - 1, Average rating: 4
(
)
)
|
manual abstract
If the link indicator does not light when main unit and subwoofer are turned on, please set the ID by following the process below. Before moving or installing the product, be sure to turn off the power and disconnect the power cord. . 1. Plug the power cords of the main unit and subwoofer into the AC power supply. . Press the id SeT button on the back of the subwoofer with a small, pointed object for 3 seconds. The STANDBY indicator is turned off and the LINK indicator (blue LED) blinks quickly. • . While main unit is powered off (STANDBY mode), press MUTe on the remote control for 5 seconds. The volume Level Indicator on the main unit lights up, then returns to STANDBY mode. . Press the POWeR button to turn on the main unit. The main unit and the subwoofer are now linked (connected). The Link indicator (blue LED) on the subwoofer is turned on. You can enjoy better sound from the wireless subwoofer by selecting the sound field mode. ( See page 16 ) • • • • POWER TV POWER TV SOURCEVOL TV CH PASS NEWS MUSIC MUTE CINEMA O/AINPUT POWER LINK AUTO MENU EXIT TOOLS INFO POWER TV POWER TV SOURCEVOL TV CH PASS NEWS MUSIC MUTE CINEMA O/AINPUT POWER LINK AUTO MENU EXIT TOOLS INFO . If the main unit is powered off, the wireless subwoofer will be in the standby mode and the STANDBY LED on the upper side will blink. . If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that uses the same frequency (2.4GHz) near the system, some sound interruption may be heard due to interference. . The transmission distance of a radio wave is about 10m, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal. . If the main unit doesn't make wireless connection, follow steps 1-4 above to retry the connection between the main unit and wireless subwoofer. . The wireless receiving antenna is built into the wireless subwoofer. Keep the unit away from water and moisture. . For optimal listening performance, make sure that the area around the wireless subwoofer location is clear of any obstructions. 1 14 connecting the CRYSTAL SURROUND AIR TRACK This section explains two ways (digital and analogue) of connecting the unit to the TV. This unit is equipped with one optical digital jack and one audio analogue jack for connecting a TV. AUDI O IN Connect AUDIO IN on the main unit to the AUDIO OUT of the TV. Be sure to match connector colours. OR, DIGI TAL IN (OPTICAL) Connect the Digital Input on the main unit to the OPTICAL OUT of the TV. Do not connect the power cord of this product or your TV to the wall outlet until all connections between components are complete. Before moving or installing this product, be sure to turn off the power and disconnect the power cord. You can connect this unit to other external components. (such as DVD player, Set-Top Box etc.) . . . DIGITAL IN (OPTICAL) AUDIG IN AUDIO IN AUDIO OUT L R OPTICAL OUT Red White DIGITAL IN (OPTICAL) Audio C able Optical C able (supplied) or 15 EnG . functions Turning the power on/off 1. Touch POWER ( ) on the front panel. OR, Press POWER on the remote control to turn on the power. The volume level appears in the front panel display. 2. Touch POWER ( ) on the front panel. OR, Press POWER on the remote control again to turn off the power. Adjusting the volume Touch VOLUME +/– on the front panel. OR, Press VOLUME +/– on the remote control to increase or decrease the volume level. The numeric value of the volume level appears in the front panel display. The volume level increases or decreases when you press VOLUME +/–. If you want to enjoy the sound only from the Crystal Surround Air Track, select EXTERNAL AMPLIFIER in the AUDIO SETUP menu of the TV. Refer to the owner's manual supplied with your TV. • • . . functions Muting the sound This is useful when answering a doorbell or telephone call. 1. Press MUTE ( ) on the remote control to mute the sound. 2. Press MUTE on the remote control again (or press VOLUME +/–) to restore the sound. Selecting the input mode You can select either Optical input or Audio input. Press O/A IN PUT on the remote control or touch IN PUT MODE on the front panel repeatedly to select the Digital (Optical) or Audio input. Input mode LED colour Digital input (Optical) PCM Red DOLBY Green DTS Blue Audio input Off PCM DOLBY DTS INPUT MODE NEWS CINEMA MUSIC POWER TV POWER VOL TV SOURCE TV CH PASS MUSIC NEWS MUTE CINEMA O/A INPUT POWER LINK AUTO MENU EXIT TOOLS INFO POWER TV POWER VOL TV SOURCE TV CH PASS MUSIC NEWS MUTE CINEMA O/A INPUT POWER LINK AUTO MENU EXIT TOOLS INFO advanced functions basic functions POWER TV POWER VOL TV SOURCE TV CH PASS MUSIC NEWS MUTE CINEMA O/A INPUT POWER LINK AUTO MENU EXIT TOOLS INFO POWER TV POWER VOL TV SOURCE TV CH PASS MUSIC NEWS MUTE CINEMA O/A INPUT POWER LINK AUTO MENU EXIT TOOLS INFO POWER TV POWER VOL ...
Other models in this manual:Receivers & Amplifiers - HT-SB1G (8.02 mb)
Receivers & Amplifiers - HT-SB1R (8.02 mb)
Receivers & Amplifiers - HT-WS1R (8.02 mb)