Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
If “MEMORY” disappears, start again from step 3. 5 While MEMORY is displayed, press the number you want to use (0 to 9). 6 Repeat Steps 2 to 5 to preset other stations. To change a preset station Preset a new station on the number you want to change. Note If the AC power cord is disconnected for about one week, the preset stations will be cleared from the receiver’s memory, and you will have to preset the stations again. Tuning preset stations (preset tuning) You can tune directly to a preset station by entering its preset number. If you don’t know which stations are preset on which numbers, you can tune by scanning the preset stations. 1 Press TUNER. The last received station is tuned in. 2 Press SHIFT to select a character (A, B or C), then press the number. For example, select A and then press 7 to tune in the station preset as A7. You can tune by scanning the preset stations First press TUNER and then press PRESET TUNING + or – to select the station you want. Each time you press the buttons, the preset numbers change as follows: n A1 . A2 . … . A0 . B1 . B2 . … . B0 N n C0 . … . C2 . C1 N Receiver Operations Receiver Operations Recording This receiver makes it easy to record to and from the components connected to the receiver. You don’t have to connect playback and recording components directly: once you select a program source on the receiver, you can record and edit as you normally would using the controls on each component. Before you begin, make sure you’ve connected all components properly. Function buttons Playback component (program source) Recording component (Tape deck, MD recorder, VCR) c c c: Audio signal flow Recording on an audio tape, MiniDisc or video tape You can record audio on a cassette tape, MiniDisc or video tape using the receiver. See the instruction manual of your tape deck, MD recorder or VCR if you need help. 1 Press one of the function buttons to select the program source. 2 Set the component to be ready for playing. For example, insert a CD into the CD player. 3 Insert a blank tape or disc into the recording deck and adjust the recording level, if necessary. 4 Start recording on the recording deck and then start playing the component. Additional InformationAdditional Information Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. There’s no sound or only a very low-level sound is heard. / Check that the speakers and components are connected securely. / Make sure you select the correct component on the receiver. / Make sure you set the SPEAKERS selector correctly. / Press MUTING on the remote if the MUTING indicator turns on. / The protective device on the receiver has been activated because of a short circuit. (“PROTECT” flashes.) Turn off the receiver, eliminate the short-circuit problem and turn on the power again. The left and right sounds are unbalanced or reversed. / Check that the speakers and components are connected correctly and securely. / Adjust the BALANCE control. Severe hum or noise is heard. / Check that the speakers and components are connected securely. / Check that the connecting cords are away from a transformer or motor, and at least 10 feet (3 meters) away from a TV set or fluorescent light. / Place your TV away from the audio components. / Make sure you connect a ground wire to the antenna ground terminal. / The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. Radio stations cannot be tuned in. / Check that the antennas are connected securely. Adjust the antennas and connect an outdoor antenna if necessary. / The signal strength of the stations is too weak (when you tune in with automatic tuning). Use direct tuning. / Make sure you set the tuning interval correctly (when you tune in AM stations with automatic tuning) (see pages 9 and 13). / No stations have been preset or the preset stations have been cleared (when you tune in with scanning preset stations). Preset the stations (see page 10). No picture or an unclear picture is seen on the TV screen. / Place your TV away from the audio components. Recording cannot be made. / Check that the components are connected correctly. The remote does not function. / Point the remote at the remote sensor g on the receiver. / Remove the obstacles in the path of the remote and the receiver. / Replace both batteries in the remote with new ones if they are weak. / Make sure you select the correct function on the remote. Additional Information Additional Information FM tuner section General Specifications Audio power specifications POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 8-ohm load, both channels driven, from 20 20,000 Hz, rated 100 watts per channel minimum RMS power, with no more than 0.1 % total harmonic distortion from 250 milliwatts to rated output. Amplifier section Dynamic power 8 ohms: 150 W + 150 W output...