Manafacture: Altec Lansing
File size: 252.51 kb
File name: 567dc7ef-445f-4b7a-880c-8f7fe7cbcccc.pdf
|
manual abstract
The amplifier provides outputs for 4-ohm, 8-ohm and 16-ohm loudspeakers, plus a 70-volt line output for distribution systems. In addition to the high-impedance input, the amplifier has an octal socket to accept a line-isolation transformer. A selectable high pass filter is included for use in speech systems. Cut-off frequency of the filter is 300 Hz. The 1593C is capable of operation from a 120V or 240V ac source or a negative grounded 28V dc source, and features silent, automatic transfer to dc operation if ac power fails. Designed for rack mounting, the 1593C occupies three vertical units of rack space (5Vi"). A hinged front panel allows servicing without removing the amplifier from the rack. г SPECIFICATIONS Type: Power Amplifier Gain: 61 dB Input Sensitivity: 0.8 volt rms for rated output Power Output: 50 watts at less than 1% THD, 50 to 12,000 Hz Frequency Response: ±1 dB, 20 to 20,000 Hz at 1 watt output. ±1 dB, 50 to 12,000 Hz at rated output. Input Impedance: 15.000 ohms (potentiometer) 600 ohms balanced with 15095A plug-in transformer 15.000 ohms balanced with 15335A transformer Load Impedance: 4, 8, 16,100 ohms Load Voltage: 14, 20, 28 (25V, 40-watt), 70 volts Output Impedance: Less than 10% of nominal load impedance Noise Level: —38 dBm or 85 dB below rated output Controls: Power on/off switch Potentiometer, continuously variable composition High-pass filter switch (rear) Power Supply: 100/120/220/240V ac, 50/60 Hz 13 watts at zero signal 85 watts at 17 watts output 145 watts at 50 watts output OR л 24/28 volts dc (battery (—) is ground 0.2 amp at zero signal 2.5 amps at 17 watts output 4.0 amps at 50 watts output Operating Temperature Range: Up to 50°C (131°F) ambient Special Features: Automatic transfer from ac to dc power in the event of ac power failure Dissipation sensing device for protection of output transistors High-pass filter (300 Hz) Dimensions: 51A" H x 19" W x 7W D (13.33 cm Hx 48.26 cm Wx 18.73 cm D) Weight: 23 pounds (10.45 kg) Color: Black Accessories (must be ordered separately): 15095A Plug-in Line Transformer 15335A Plug-in Bridging Transformer Design and Underwriters Laboratories list- Performance ing 209J for Commercial Audio Approvals: Systems, File E8783(N) Underwriters Laboratories listing 89MO for Fire Protective Signaling Systems, File S2925(N) ARCHITECT'S AND ENGINEER'S SPECIFICATIONS The power amplifier shall be capable of operating from a 100/120/220/240V ac line or from a 24/28V dc battery. The power supply shall automatically transfer the power to dc operation if ac power fails. An octal socket shall be provided on the rear panel for installation of an accessory line transformer. The front panel shall be hinged to permit access to the chassis interior without removing the amplifier from the equipment rack. The power amplifier shall meet the following performance criteria. Gain, 61 dB. Input sensitivity, 0.8V rms for rated output. Power output, 50 watts at less than 1% THD from 50 Hz to 12 kHz. Frequency response at 1 watt output, ± 1. dB from 20 Hz to 20 kHz and ± 1 dB 50 Hz to 12 kHz at rated output. Input impedance: 15,000 ohms (potentiometer), 600 ohms balanced with 15095A plug-in transformer, 15,000 ohms balanced with 15335A transformer. Load impedance; 4, 8, 16 and 100 ohms. Load voltage; 14, 20, 28 (25V, 40-watt), and 70 volts. Output impedance, less than 10% of nominal load impedance. Noise level, -38 dBm or 85 dB below rated output. Operating temperature range up to 55°C (131°F) ambient. Dimensions, 5’/4" H x 19” W x 7V&" D. Weight, 23 pounds. Color, black. The power amplifier shall be Underwriters Laboratories listed for use in commercial aucfio systems and fire protection signaling systems. ALTTEIC LANSING P.O. BOX 26105, OKLAHOMA CITY, OK 73126-0105, U.S.A ©1989 ALTEC LANSING CORPORATION PRINTED IN U.S.A. 989 REVISION 6 AL-1782 42-07-027036...