Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
This unit is for use in DC 12V, negative ground vehicles. 2. Do not operate the unit in ways other than described in this guide. Doing so may damage it and may void your warranty. 3. SAFETY FIRST! For rear seat use only. Do not install monitors displaying video information anywhere that would permit viewing by the driver. Monitors must not be located in the motor vehicle at any point forward of the back of the front seats. Monitors must never be used in any manner that will distract driver or interfere with driver’s safe operation of the motor vehicle. 4. Be careful not to run down the car battery while using the unit with the car stopped. 5. Do not disassemble or modify the unit. Doing so may damage it and voids your warranty. 6. Keep drinks and drops from umbrellas away from the unit. Water may damage the internal circuitry. 2 7. Do not let the unit become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. DESCRIPTION The Clarion TTX001 TV tuner has a number of exceptional features. For instance, the TTX001 allows two types of wiring: stand alone or with the Clarion VMA1131. It also has preset tuning (for a total of 12 VHF/UHF stations), manual tuning and automatic tuning to permit easy tuning of the desired broadcast stations. PACKAGE CONTENTS The TTX001 comes with the following items: • TV tuner • RC-300 remote control • 16 pin to A/V, IR and power inputs • IR Receiver • A/V RCAcable • Power harness • 3.5mm Male to Male IR extension • Y connector for IR CONNECTORLOCATIONS Figure 1- 1 3.5mm Antenna Connector 2 IR Sensor 3 Connector 4 IR Sensor Connector 5 Video Output Connector 6 R Audio Output Connector 7 L Audio Output Connector 8 Power Connector 9 IR Input Connector 3 WIRING PRECAUTIONS Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer. 1. Disconnect the negative (-) lead of the battery before making any power connections. 2. When creating passage holes for the power wires, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit. 3. When connecting the ground lead, fasten the ground lead (black) securely to a clean metal plate on the vehicle. Figure 2- Wiring 4 APPLICATIONS The TTX001 can be operated in a number of applications. Find yours below. With the VMA1131 1. Place tuner into the channel on the back of the monitor and slide the tab into the slot. Mount tuner with the two machine screws supplied. 2. Plug the 16 to 16 pin cable (supplied with the monitor) into the tuner and the back of the monitor. 3. Mount the antenna (ZCB-003 or equivalent) and plug into the antenna input of the tuner. 4. Plug the power connector into the monitor and connect to vehicle accessory and ground. Operation • The tuner can be controlled by the buttons on the monitor or by the remote control. Figure 3- TTX001 with VMA1131 5 With the VDH9600, OHM641 and the FM100S 1. Pick a location to mount the tuner. Typically the tuner will be located close to the VCP. Avoid areas with excessive heat or moisture and mount the tuner. 2. Mount the TV antenna (ZCB-003 or equivalent) and plug into the tuner. 3. Plug the 16 pin to A/V out connector into the tuner. Plug the A/V RCA cables, IR extension and power plug into the 16 pin connector and run to the video player. 4. Plug the A/V RCA cable into the A/V input of the player. Plug the Y connector into the player and plug the IR extension into the Y connector. 5. At the OHM641, plug the IR extension and power cables supplied with the OHM641. Run these cables to the back of the video player. Plug the video RCA into the video output of the player. Plug the IR extension into the other leg of the Y connector. Tie all the power wires together. These wires will be run to the radio location. 6. Plug the audio RCA cable into the audio output of the player and run the audio RCA and main power cables to the radio location. Remove the radio and plug the audio RCA into the FM100S audio inputs. 7. Mount the switch for the FM100S and run its power wire to the radio location. The power and ground wires of the TTX001, video player, OHM641 and the FM100S can be joined and connected to the radio accessory and ground wires. 8. Plug the vehicle antenna into the antenna input of the FM100S. Plug the antenna output of the FM100S into the radio. 9. The FM 100S has a two position switch to select the modulation frequency. Pick the frequency that has the least amount of radio reception and set that frequency on the modulator and into a radio preset memory. Operation • Similar to a home system, the VDH9600 allow their auxiliary A/V inputs to loop through to their A/V outputs when they are not playing a video tape. • Because the IR lines have been linked together, each component can be controlled by its respective remote control when pointed to the IR eye located on OHM641. • Turn the vehi...