Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
0717A Set Zone 2 (B) product ID - Each message transmitted from your remote includes a Product Code, identifying the manufacturer, and Zone product ID code from 1 to 16. The product ID code allows multiple B&K products to be controlled from the same remote. Your receiver actually uses two product ID codes -one for Zone 1 (A) (normally set to ID code 1) and the other for Zone 2 (B) (normally set to ID code 2). If you have a system with multiple B&K products then you may wish to set the Zone product ID codes to other values. Note that you cannot set the Zone 1 (A) product ID to the same setting as Zone 2 (B) or vice versa. If you need to set Zone 1 (A) to the current Zone 2 (B) setting then set Zone 2 (B) to some other value first. Set Zone 2 (B) product ID - Each message transmitted from your remote includes a Product Code, identifying the manufacturer, and Zone product ID code from 1 to 16. The product ID code allows multiple B&K products to be controlled from the same remote. Your receiver actually uses two product ID codes -one for Zone 1 (A) (normally set to ID code 1) and the other for Zone 2 (B) (normally set to ID code 2). If you have a system with multiple B&K products then you may wish to set the Zone product ID codes to other values. Note that you cannot set the Zone 1 (A) product ID to the same setting as Zone 2 (B) or vice versa. If you need to set Zone 1 (A) to the current Zone 2 (B) setting then set Zone 2 (B) to some other value first. ADVANCED ZONE B SETTINGS 1 Level Control Variable 2 Fixed Level +15 dB 4 V2 Output Tape 5 Link Input to Zone A No 6 Link Power to Zone A No next item adjust MENU advanced setup 3 Zone ID 2 =%=21(,' From Remote From Front Panel Action 1 (PAUSE) or .(STOP) U (UP) or U (DOWN) move to Zone ID 2 .(REW) or.(FF) VOLUME KNOB adjust Zone 2 (B) ID to desired value Set V2 line output usage - V2 output is normally set up as a tape loop. The V2 and Zone 2 (B) output are the current source (V1, TV, CD, DVD, etc.) except when the current selection is V2. When V2 is selected as the source, the Zone 2 (B) output is V2 and the V2 output is the previously selected source. This prevents feedback when the V2 inputs and outputs are connected to a tape deck or VCR. Feedback can cause high frequency oscillations which may damage your speakers. If you don’t connect a tape deck to the V2 input and output you can use the V2 output as an additional line out. In this mode V2 output is always the selected input including V2. ADVANCED ZONE B SETTINGS 1 Level Control Variable 2 Fixed Level +15 dB 3 Zone ID 2 5 Link Input to Zone A No 6 Link Power to Zone A No next item adjust MENU advanced setup 4 V2 Output Tape ADVANCED ZONE B SETTINGS 1 Level Control Fixed 2 Fixed Level +15 dB 3 Zone ID 2 5 Link Input to Zone A No WARNING Connecting a tape recorder to V2 in LINE mode can cause speaker damage next item adjust MENU advanced setup 4 V2 Output Line =. 9. 28. 7$3. =. 9. 28. /,1. From Remote From Front Panel Action 1 (PAUSE) or .(STOP) U (UP) or U (DOWN) move to V2 Output 2 .(REW) or.(FF) VOLUME KNOB set for Tape or Line 66 p/n 12858 Rev. 0717A (B) selection. ADVANCED ZONE B SETTINGS 1 Level Control Variable 2 Fixed Level +15 dB 3 Zone ID 2 4 V2 Output Tape 6 Link Power to Zone A No next item adjust MENU advanced setup 5 Link Input to Zone A No =%/,1.65&12 From Remote From Front Panel Action 1 (PAUSE) or .(STOP) U (UP) or U (DOWN) move to Link Input to Zone A 2 .(REW) or.(FF) VOLUME KNOB set to Yes or No Link Zone 2 (B) power to Zone 1 (A) power - Zone 2 (B) power On/Off may be linked to Zone 1 (A). In operation, whenever power is set to On in Zone 1 (A) the power linkage feature will cause power to be set accordingly on Zone 2 (B). Zone 2 (B) Independent power on/off is still operational with the Zone 2 (B) remote control, but any Zone 1 (B) power command supersedes the previous Zone 2 (B) power on/off. ADVANCED ZONE B SETTINGS 1 Level Control Variable 2 Fixed Level +15 dB 3 Zone ID 2 4 V2 Output Tape 5 Link Input to Zone A No next item adjust MENU advanced setup 6 Link Power to Zone A No =%/,1.3:512 From Remote From Front Panel Action 1 (PAUSE) or .(STOP) U (UP) or U (DOWN) move to Link Power to Zone A 2 .(REW) or.(FF) VOLUME KNOB set to Yes or No 3 MENU . MENU return to ADVANCED SYSTEM SETUP 67 p/n 12858 Rev. 0717A Power On Titles Power On Titles ADVANCED SYSTEM SETUP 1 Zone 1 Setup 'A' 2 Zone 2 Setup 'B' 4 Control Out 5 Security Options 6 DSP Usage 7 RS-232 Control Port next item SEL select MENU setup system 3 Power On Titles POWER ON TITLES ' BK Components ' 2 Power On Line 2 ' * Digital DNA ' next item SEL edit MENU advanced setup 1 Power On Line 1 32:(5217,7/(632:(521/,1( return to ADVANCED SYSTEM SETUP. MENUMENU11 edit Line 2repeat 4 - 8repeat 4 - 810 move to Power On Line 2U (UP) or U (DOWN)(PAUSE) or .(STOP)9 finish editing line 1. (ENTER)SEL or ENTER 8 continue changing charactersrepeat 5 - 6repeat 5 - 67 move to new characterVOLUME KNOB.(REW) or.(FF)6 change blinking characterU (U...
Other models in this manual:Receivers & Amplifiers - AVR307 (1.11 mb)