Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be placed between it and the furniture. • Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or similar materials can damage the surface of the unit. FCC Information FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. SDI Technologies Inc. 1299 Main Street, Rahway NJ 07065 Tel. No.: (732) 574-9000 Quick Start 2:inserts Select the dock insert for your iPod model from the table below and place insert in dock. Never dock an iPod without an insert in place. 3:iPod Insert iPod into dock with proper insert (iPod must not be in a skin or case). iPod will charge while docked. Press iPod Button on iH11 to play iPod. iPod Touch thin iPod with video (30 GB) Insert 9 3rd Gen nano insert 13 3rd Gen nano iPod with video (60,80 GB) Insert 10 thin (30 GB) iPod with video thin (80GB) iPod classic thick (60, 80 GB) iPod with video thick (160 GB) iPod classic iPod Touch insert 14 For this iPod Use this insert 1:power Attach AC adaptor cable to jack on back of the iH11 and plug the other end into a wall socket. DC 10Vline in clock adj. dst -1 +1 on o NOTE: If the insert for your iPod isn’t listed, please visit an Apple store or to purchase the proper insert. 4:time • Move the DST switch on the back of the unit to +1 or -1 (adds or subtracts an hour to account for daylight saving time). • Press & Hold the Clock adj. button on the back of the unit until the display flashes. • Press the Hour Set / Minute buttons to set current time. • Press the Clock Adj. button again to confirm time setting. 1 Controls and Indicators Controls and Indicators Alarm Set / Front Panel Alarm On/Off Button . iPod Dock Power Off / . iPod Play/Pause Button Alarm Reset Button . . Hour Set Button Snooze/Dimmer Button . . Sleep/Minute Set Button . Volume + Button . Volume - Button Remote Sensor Back Panel Clock Adj. Button . DST Switch . . EXB Expanded Bass Switch . DC Jack Line-in Jack . DC 10Vline in clock adj. dst -1 +1 on o 2 iH11 Display iH11 Display Alarm IndicatorTime Display PM Indicator Battery Low Indicator Daylight Saving Time Indicator iPod Indicator Sleep Indicator Install Clock Backup Battery The iH11 uses a CR2032 button cell backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Backup Battery has been installed and a power failure occurs or the AC adaptor is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Open backup battery compartment door located on the backside of the unit. 3. Insert one CR2032 button cell battery, checking that the polarity (+ and – sides of the battery) matches the drawing in the battery compartment. Close the compartment door. Note: Make sure you dispose of batteries properly (see your local regulations). Installing Backup Battery . 3 Using The Optional Remote Control Unit . iPod Play/Pause Button . Power Off /Alarm Reset Button . Forward Button . Reverse Button Volume - Button . . Volume + Button Sleep Button . . Mute Button . Snooze/Dimmer Button Install/Replace the Remote Control Battery The remote control batt...