Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Pause Feature A four (4) second pause may be inserted into the speed dialing of the telephone numbers. Press the RD/P button at the required point during storage of a number into memory. 16 UG060205_C410_RevA.qxd 6/15/05 8:03 PM Page 17 Operating Your Telephone Lighted Key Pad The key pad will light for fifteen (15) seconds after removing from the base when there is an incoming call. To reactivate the feature while in standby or in use, press any key. Page / Handset Locator To send a page signal from the base to the handset, press the PAGE button located on the base of the telephone. A series of rings will sound from the handset. To locate the handset if it is away from the base, press and hold the PAGE button for approximately five (5) seconds. A series of rings will sound for approximately sixty (60) seconds. Return the handset to the base or press the TALK button to cancel the page. Press TALK again to return to standby mode. 40 Channel Operation The C410 cordless telephone automatically searches and selects the clearest of 40 channels when it is being used. Security Code The security code prevents your cordless phone from being accessed by a phone on a different line. Once the handset battery is fully charged, the handset will automatically select the code from over 65,000 combinations. The code is changed every time the handset is placed in the cradle. If you have trouble with placing or receiving calls, a lost security code may be the cause of the problem. When this occurs, the handset can no longer communicate with the base. Reset by placing the handset on the base for 5-10 seconds. If that does not work, unplug the AC adapter from the wall outlet. Disconnect the handset battery for 5-10 seconds, and then reconnect. Place handset back on the base and then reinsert the AC adapter. Hearing Aid Compatibility The handset has a special coil inside of it to couple the sound to hearing aids equipped with T-Switches/T-Coils. ENGLISHE N G L I S H 17 UG060205_C410_RevA.qxd 6/15/05 8:03 PM Page 18 Operating Your Telephone MEMORY STORAGE Emergency Storage Buttons Three emergency buttons are located on the handset. These storage buttons can be programmed with numbers of up to 16 digits. Memory Storage Locations The C410 also has 10 indirect or two touch memory locations on the telephone (0-9) that can be programmed to dial frequently called numbers of up to 16 digits. To Store numbers into memory 1. Press the MEM button. 2. Dial the number you wish to store. 3. Press the MEM button again. 4. Press either the emergency button or the number on the dial pad that you wish to store the number to. 5. A long beep will indicate the programming process is complete. During the memory storage process the TALK button will flash GREEN. In the event of a power outage memory is retained of at least six (6) hours. To Change a Number Stored into Memory Replace a stored number by programming a new number in its place. To Delete a Number Stored into Memory 1. Press and release the MEM button. 2. Press the * key once for each digit in the number you are deleting. 3. Press the MEM button again. 4. Press the button for the memory location you want to delete the number from. 18 UG060205_C410_RevA.qxd 6/15/05 8:03 PM Page 19 Operating Your Telephone MAKING AND RECEIVING PHONE CALLS Placing a Phone Call 1. Press the TALK button. (TALK button will illuminate). 2. Dial the number you wish to call. 3. Adjust the rotary Volume Control to desired level. 4. Press the Clarity Power Button (activates the Clarity Power Technology) to gain the extra level of amplification, if needed. Refer to BOOST CLARITY POWER ON/OFF and BOOST ON/OFF for additional information on volume controls. To Dial from Memory 1. Press the TALK button. 2. Press the MEM button. 3. Press the number on the dial pad where the desired number has been stored. 4. The call will automatically dial. 5. Adjust volume and Clarity Power as needed. To Dial From Emergency Storage Location 1. Press the TALK button. 2. Press the desired emergency button. 3. The call will automatically dial. 4. Adjust volume and Clarity Power as needed. To use a TONE service on a Pulse Line 1. Dial the number you wish to call 2. When the call is answered, press the * key. Additional numbers you dial are sent as tone signals. 3. After completing the call, press TALK or return the handset to the base. The phone will automatically reset. Receiving a Call Handset in Base of Telephone 1. Lift the handset. Do not press TALK. You will automatically be connected. Handset out of Base 1. Press the TALK button. Ending a Call Place the handset in the base cradle or press the TALK button to disconnect the line. Note: When placing or receiving a call, the handset visual ringer will lite, indicating the phone is in use. ENGLISHE N G L I S H 19 UG060205_C410_RevA.qxd 6/15/05 8:03 PM Page 20 Troubleshooting The Unit Will Not Operate/No Dial Tone • Verify the TALK Button is lit. • Verify the AC adapter is securely plugged in...