(V.M.: Voice mail) {3}{3}{1} – r 36 TalkingCallerID (Handset) {1}{6}{2} {1}: {0}: Off – 27 For assistance, please visit Programming Feature Feature code Setting code System setting*1 Page TalkingCallerID (Base unit) {*}{1}{6} {2} {1}: On {0}: r 27 Time adjust*10 (Caller ID subscribers only) {2}{2}{6} {1}: {0}: Manual r – V.M. access (V.M.: Voice mail) {3}{3}{0} – – 37 VM tone detect (VM: Voice mail) {3}{3}{2} {1}: {0}: Off r 36 Voice prompt(Change language) {1}{1}{2} {1}: {2}: Espanol r 12 *1 If “System setting” column is checked, you do not need to program the same item using another handset. *2 If you subscribe to a Caller ID service and want to view the caller’s information after lifting up the handset to answer a call, turn off this feature. *3 The handset can display the Internet address where you can download the operating instructions or get further information for this product, using your computer. *4 Turn this feature off if you prefer not to hear key tones while you are dialing or pressing any keys, including confirmation tones and error tones. *5 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 to 3). If you select a melody, you cannot distinguish lines by their ringers. *6 If you select one of the melody ringer tones, the ringer tone continues to play for several seconds even if the caller has already hung up. You may either hear a dial tone or no one on the line when you answer the call. *7 When the ringer volume is turned off, ~ is displayed and the handset does not ring for outside calls. However even when the ringer volume is set to off, the handset rings at the low level for alarm (page 23), and intercom calls, and paging (page 38). *8 The flash time depends on your telephone exchange or host PBX. Contact your PBX supplier if necessary. The setting should stay at “700ms” unless pressing {FLASH} fails to pick up the waiting call. *9 Generally, the line mode setting should not be adjusted. If S is not displayed when another phone connected to the same line is in use, you need to change the line mode to “A”. *10This feature allows the unit to automatically adjust the date and time setting when caller information is received. To use this feature, set the date and time first. For assistance, please visit Programming Special programming Silent mode Silent mode allows you to select a period of time during which the handset will not ring for outside calls. This feature is useful for time periods when you do not want to be disturbed, for example, while sleeping. Silent mode can be set for each handset. Important: LSet the date and time beforehand (page 12). LWe recommend turning the base unit ringer off (page 14) and call screening off (page 30) in addition to turning the silent mode on. LIf you have set the alarm, the alarm sounds even if the silent mode is turned on. Turning silent mode on/off 1 {MENU} (center of joystick) i {#}{2}{3}{8} 2 {V}/{^}: Select “On” or “Off”. i {SAVE} LIf you select “Off”, press {OFF} to exit. 3 Enter the desired hour and minute you wish to start this feature. 4 {AM/PM}: Select “AM” or “PM”. i {OK} 5 Enter the desired hour and minute you wish to end this feature. 6 {AM/PM}: Select “AM” or “PM”. 7 {SAVE}i {OFF} LWhen the silent mode is set, &is displayed. Note: LTo correct a digit, push the joystick left or right to move the cursor to the digit, then make the correction. Changing the start and end time 1 {MENU} (center of joystick) i {#}{2}{3}{7} 2 Continue from step 3, “Turning silent mode on/off”, page 23. Alarm You can set one of 2 different alarm options (once or daily) at a time for each handset. An alarm sounds at the set time for 1 minute. The following alarm sounds are available: – “Tone/Melody”: You can choose an alarm sound from 3 tones and 4 melodies. – “Voice”: You can choose one of the 7 pre-recorded announcements: – “Good morning” – “It’s time for dinner” – “It’s time for lunch” – “It’s time for the game” – “It’s time for your meeting” – “It’s time to pick up the children” – “Happy birthday” The unit makes the selected announcement at the set time (talking alarm clock). Important: LSet the date and time beforehand (page 12). 1 {MENU} (center of joystick) i {#}{7}{2}{0} 2 {V}/{^}: Select the desired alarm option. i {SELECT} Off Turns alarm off. Go to step 6. For assistance, please visit Programming Once An alarm sounds once at the set time. Enter the desired month, date, and year. i {OK} Daily An alarm sounds daily at the set time. 3 Set the desired time. i {OK} 4 {V}/{^}: Select “Tone/Melody” or “Voice”. i {SELECT} 5 {V}/{^}: Select the desired item. i {SAVE} LIf you set a tone or melody, we recommend selecting a different one for outside calls. 6 {OFF} LWhen the alarm is set, Eis displayed. Note: LTo stop the alarm, press any dial key or place the handset on the base unit or charger....
)
