Votes - 2, Average rating: 4.5
(
)
)
|
Other manuals for this model:
Cordless Phones - KXTG6311 (423.13 kb)
Cordless Phones - KXTG6311 (419.14 kb)
manual abstract
2 When you finish talking, press {INTERCOM}. Answering an intercom call Handset 1 Press {C} to answer the page. 2 When you finish talking, press {OFF}. Base unit ¦ KX-TG6322/KX-TG6323/ KX-TG6324 1 Press {INTERCOM} to answer the page. 2 When you finish talking, press {INTERCOM}. Note: L When the ringer volume for outside calls is set to off (page 18, 24), the handset and/or base unit rings at a low level for intercom calls. Transferring calls, conference calls Outside calls can be transferred between 2 handsets. 2 handsets can have a conference call with an outside party. 1 During an outside call, press {INTERCOM} to put the call on hold. 2 {V}/{^}: Select the desired unit. i {Transfer} 3 Wait for the paged party to answer. L If the paged party does not answer, press {C} to return to the outside call. 4 To complete the transfer: Press {OFF}. L The outside call is being routed to the destination unit. For assistance, please visit Intercom/Locator To establish a conference call: Press {Conf}. L To leave the conference, press {OFF}. The other parties can continue the conversation. L To put the outside call on hold, press {HOLD}. To resume the conference, press {Conf}. Answering a transferred call Press {C} to answer the page. Note: L After the paging party disconnects, you can talk to the outside caller. Handset locator You can locate a misplaced handset by paging it. 1 Base unit: {LOCATOR} L All registered handsets beep for 1 minute. 2 To stop paging: Base unit: Press {LOCATOR}. Handset: ¦ KX-TG6311/KX-TG6312/ KX-TG6313 Press {OFF}. ¦ KX-TG6322/KX-TG6323/ KX-TG6324 Press {INTERCOM}, then press {OFF}. Note: L When the ringer volume for outside calls is set to off (page 24), the handset rings at a low level for paging. For assistance, please visit Useful Information 42 For assistance, please visit Wall mounting Base unit 1 Lead the telephone line cord through the hole in the wall mounting adaptor in the direction of the arrow. 2 Tuck the telephone line cord inside the wall mounting adaptor (A). Connect the AC adaptor cord and telephone line cord (B). 3 Insert the hooks on the wall mounting adaptor into the holes 1 and 2 on the base unit. 4 Adjust the adaptor to hold the base unit, then push it in the direction of the arrow until it clicks into place. Hook A B 1 1 2 1 2 2 83 mm (3 1/4 inches) 102 mm (4 inches) 1283 mm (3 1/4 inches) 102 mm (4 inches)12 Useful Information ABC 5 Connect the telephone line cord. Mount the unit by inserting the mounting pins into the round openings on the adaptor (for pin 2, use the round cut out at the bottom of the adaptor if you are using the 4 inch phone plate), then slide the unit down to secure it. Connect the AC adaptor to power outlet (page 12). L There are 2 common types of wall phone plates. The distance between 1 and 2 may vary depending on the size of the wall phone plate installed. 12 (120 V AC, 60 Hz) 83 mm (3 1/4 inches) or 102 mm (4 inches) To remove the wall mounting adaptor While pushing down the release levers (A), remove the adaptor (B). ABA Charger Available for: KX-TG6312/KX-TG6313/ KX-TG6322/KX-TG6323/KX-TG6324 1 Drive the screws (not included) into the wall. 25.4 mm (1 inch) Screws (120 V AC, 60 Hz) 2 Mount the charger (A), then slide it down (B) and to the right (C) until it is secure. For assistance, please visit Useful Information Error messages If the unit detects a problem, one of the following messages is shown on the display. Display message Cause/solution Busy or System is busy. Pleasetry again later. L The called handset or base unit is in use. L Other units are in use and the system is busy. Try again later. L The handset you are using is too far from the base unit. Move closer and try again. L The handset’s registration may have been canceled. Re-register the handset (page 28). Check tel line L The supplied telephone line cord has not been connected yet or not connected properly. Check the connections (page 12). Don’t use this battery. L A wrong type of batteries such as Alkaline or Manganese was inserted. Use only the rechargeable Ni-MH batteries noted on page 6, 13. Error!! L The handset’s registration has failed. Move the handset and base unit away from all electrical appliances and try again. Insert battery L The handset was placed on the base unit or charger without batteries. Insert the batteries properly (page 13). Invalid L There is no handset registered to the base unit matching the handset number you entered. L The handset is not registered to the base unit. Register the handset (page 28). No link to base. Reconnect AC adaptor. L The handset has lost communication with the base unit. Move closer to the base unit and try again. L Unplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. L The handset’s registration may have been canceled. Re-register the handset (page 28). Phonebook full L T...