Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
1 1 Press (FUNCTION/2WAY!REC). 2 2 Scroll to “Program” by pressing O or N. 3 3 Press a. 4 4 Press a at “TAD program”. 5 5 Press a at “Day and time”. •“Set time” is announced from the base unit. If previously adjusted, the day/time will be heard. Ringer pattern HProgram HTAD program Set flash time HDay and time Remote code SUN 12:00 AM #=Day 0-9=Time =AM/PM H=Save 6 Enter the current time (hour and minute) using a 4-digit number. (Ex. To set 9:30, enter “0930”.) 7 Press (*) to select “AM” or “PM”. Press (#) repeatedly to set the day. SUN 09:30 AM #=Day 0-9=Time =AM/PM H=Save MON 09:30 AM #=Day 0-9=Time =AM/PM H=Save MON 09:30 AM 8 8 Press a (Save key). •The base unit announces the day/time. The clock starts working. •If 6 beeps sound from the base unit, the setting is not correct. Start again from step 5. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF). •In step 6, you cannot enter numbers greater than 12. Do not use military time. (To set 13:00 hours, enter “0100”, and select “PM” by pressing (*).) If a power failure occurs, the time may be shifted. When “ ” flashes on the base unit display, reprogram the current day/time. To check the day/time Repeat steps 1 to 5 on page 26. •The base unit announces the current day/time displayed on the handset. When finished, press (OFF). For Caller ID service users (p. 37) •The Caller ID information will reset the clock after the first ring if the adjusted time is incorrect. However, the day will not be reset by the Caller ID information. Adjust the correct day by following the steps on page 26. •If the time has not previously been set, the Caller ID information will not adjust the clock. •The Caller ID information will automatically adjust the clock for daylight saving time. Preparation 27 For assistance, please call: 1-800-211-PANA(7262) Preparing the Answering System Caller’s Recording Time You can select “1 minute”, “2 minutes”, “3 minutes” or “Greeting only” for the caller’s recording time. Your phone comes from the factory set to “3 minutes”. Make sure the unit is not being used and the handset is lifted off the base unit. 1 1 Press (FUNCTION/2WAY!REC). 2 2 Scroll to “Program” by pressing O or N. Ringer pattern HProgram 3 3 Press a. HTAD program Set flash time 4 4 Press a at “TAD program”. HDay and time Remote code 5 5 Scroll to “Recording time” by pressing Number of ring O or N. HRecording time 6 6 Press a. Recording time :3min •The current setting is displayed. GF H=Save 7 7 Select the recording time by pressing O or N. •You can also select the recording time by pressing dialing buttons (1) (1 minute), (2) (2 minutes), (3) (3 minutes) or (0) (Greeting only). Press a (Save key). Recording time8 •A beep sounds from the base unit. :Greeting only •To exit the programming mode, press (OFF). •If “Greeting only” is selected, the base unit display will become blank. •You can exit the programming mode any time by pressing (OFF). If you select “Greeting only”, the unit will answer a call with the greeting message, and then hang up. The unit will not record any incoming messages. PreparationYou can select the number of times the unit rings before the answering system answers a call, from “2” to “7” or “Toll saver”*. Your phone comes from the factory set to “4”. Ringer pattern HProgram -------------------------- HTAD program Set flash time Make sure the unit is not being used and the handset is lifted off the Number of Rings base unit. 1 1 Press (FUNCTION/2WAY!REC). 2 2 Scroll to “Program” by pressing O or N. 3 3 Press a. 4 4 Press a at “TAD program”. -------------- HDay and time Remote code 5 5 Scroll to “Number of ring” by pressing O or N. 6 6 Press a. •The current setting is displayed. Remote code HNumber of ring Recording time Number of rings :4 GF H=Save 7 7 Select the number of rings by pressing O Number of rings or N. :Toll saver GF H=Save •You can also select the number of rings by pressing dialing buttons (2) to (7) or (0) (Toll saver*). 8 8 Press a (Save key). Number of rings :Toll saver •A beep sounds from the base unit. •To exit the programming mode, press (OFF). •You can exit the programming mode any time by pressing (OFF). *Toll saver If the unit answers on the 2nd ring, there is at least one new message. If the unit answers on the 4th ring, there are no new messages. Hang up when you hear the 3rd ring. This will save you the toll charge for the call. 29 For assistance, please call: 1-800-211-PANA(7262) Making Calls Handset 1 1 Press . Back side Speaker (OFF) (REDIAL/PAUSE) Display , , Microphone .. (HOLD/INTERCOM/CLEAR) Talk Talk 1112222 Talk 00-00-00 Off 00-01-08 2 2 Dial a phone number. •The dialed number is displayed. •After a few seconds, the display will show the length of the call and the battery strength. 3 3 To hang up, press (OFF) or place the handset on the base unit. •If the handset has lost communication with the base unit, 3 beeps sound and “No link to base Place on cradle and try again.” i...