Votes - 1, Average rating: 3
(
)
)
|
manual abstract
press ^ ISP-PHONEl • The indicator light goes out I FLASH I • For best speakerphone performance, use in a quiet room and speak alternately with the caller • While using the speakerphone, if the handset is on the base unit, you may switch to the handset by lifting it up To redial the last number Press I SP-PHONE I + I REDIAL/PAUSE I To adjust the speaker volume (12 levels) To increase, press /\ To decrease, press v I REDIAL/PAUSE ISP-PHONEl and Indicator- MIC [HOLD] 12 To put a call on hold Press I HOLD! • The SP-PHONE indicator flashes • If you put a call on hold for 6 minutes, a warning tone will sound The call will be disconnected after a total of 10 minutes To release the hold Press I SP-PHONE I or lift the handset off the base unit • If another phone is connected on the same line, you can also release the hold by lifting its handset Answering Calls with the Base Unit 1 Press ISP-PHONEI 2 3 Speak into the MIC To hang up, press I SP-PHONE I To select the ringer volume Set the RINGER selector to HIGH, LOW, or OFF • When set to OFF, the base unit will not ring 13 Automatic Dialing (Handset) Storing Phone Numbers in Memory You can store 10 numbers in the handset The dialing buttons (0 to 9) function as memory stations The TALK indicator light must be off Press I PROGRAM I • The BATT LOW/PROG indicator lights П Enter a phone number up to 16 digits • If you misdiai, press I PROGRAM I to end storing, then restart from step 1 Press I AUTO Press a memory station number (0 to 9) • A confirmation tone sounds (See below) • To store other numbers, repeat steps 1 through 4 What the confirmation tone means 1 beep The new number is stored 2 beeps The number is the same as a previously stored one I AUTO I I PROGRAMI BATT LOW/ PROG Indicator 14 To erase a stored number Press I PROGRAM! » I AUTO number to be erased) Memory sticker You may use one of the included memory stickers as a memorandum for automatic dialing Write down the names or phone numbers, then attach it to the unit or at a convenient place Dialing a Stored Number 1 2 3 the memory station number (for the phone Press [TALK] Press I auto] Press the memory station number (0 to 9) • The stored number is dialed 1" tfOjSTA TtOÑjA Öf.OÜA TICJDIA ИЕйШ t 6 2 7 3 8 4 9 5 0 [ TEL NO J J • Numbers stored m the handset can only be dialed with the handset 15 Basic Operation Automatic Dialing (Base Unit) Storing Phone Numbers in Memory You can store 10 numbers in the base unit The dialing buttons (0 to 9) function as memory stations The SP-PHONE indicator light must be off Press I PROGRAM I • The IN USE/CHARGE/ PROG indicator flashes Enter a phone number up to 16 digits • If you misdial, press I PROGRAM I to end storing, then restart from step 1 Press I AUTO IN USE/CHARGE/PROG Indicator A Press a memory station * number (0 to 9) • A confirmation tone sounds (See below) • To store other numbers, repeat steps 1 through 4 What the confirmation tone means 1 beep The new number is stored 2 beeps The number is the same as a previously stored one 16 To erase a stored number Press I PROGRAM I + I AUTO I number to be erased) Memory sticker You may use one of the included memory stickers as a memorandum for automatic dialing Write down the names or phone numbers, then attach it to the unit or at a convenient place Dialing a Stored Number 1 the memory station number (for the phone PresslSP-PHQNEl 2 3 Press I auto) Press the memory station number (0 to 9) • The stored number is dialed - |7 OlSTA TJONJA ÜJ.OtoATJClDÍAHERM t 6 г 7 3 8 4 9 5 0 [ TEL NO J L_ .. J Numbers stored in the base unit can only be dialed with the base unit 17 Basic Operation Intercom A 2-way intercom is available between the handset and the base unit Paging the base unit from the handset H Handset Press (IntercomI, then speak Base unit When the other party’s voice is heard, answer through the MIC Handset To end the intercom, press I INTERCOM I MIC Paging the handset from the base unit (Handset locator) Using this feature, you can locate the handset if misplaced ■j Base unit Press I LOCATOR/INTERCOM I • The handset beeps for 1 minute • To stop paging, press I locator/intercom] again Handset LOCATOR/INTERCOM 3 4 Press I INTERCOM I to answer Base unit Speak into the MIC Handset To end the intercom, press I INTERCOM I 18 During the intercom: • Intercom calls can only be ended with the handset. • If the handset user has difficulty hearing the base unit user, decrease the speaker volume by pressing v . • If two tones sound, it means an incoming call has been received. To answer, press I TALKl or I sp-PHONE I. The intercom is ended. Transferring a Call Using Intercom The intercom can be used during a call. This feature enables you to transfer the call between the handset and the base unit. From the handset to the base unit From the base u...