Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Mount the unit, then slide down. • Raise the antenna. To charge the battery: Place the handset on the handset hook as shown. • The IN USE/CHARGE indicator lights. 20 Making Calls 1 ITALKI and Indicator IR E DIAL/PA USE] \ [LOUD] Press ¡TALK). • The TALK indicator lights. • The selected channel number is displayed. Dial a phone number. • The dialed number is displayed. • After a few seconds, the display will show the length of the call and the present battery strength. Talk CH10 Talk 1112222 CH10 Talk 00-00-00 (III] O To hang up, press I TALK] or place the ^ handset on the base unit. • The indicator light goes out. • If “Out of range” is displayed and an alarm tone sounds in step 1, move closer to the base unit or place the handset on the base unit. Then try again. To redial the last number dialed Press ITALKI ■* I REDIAL/PAUSE]. Making Calls To select the receiver volume Press (LOUD] while talking. • Each time you press the button, the volume level will change from MEDIUM (preset) to HIGH to LOW. • The display will return to the length of the call. MEDIUM HIGH Loud Low 1111 High Loud Low HIIIII High V LOW Loud Low fi 1 High If noise interferes with the conversation Press I CHI to select a clearer channel or move closer to the base unit. • The selected channel number is displayed. Backlit LCD display The lighted display will stay on for about 10 seconds after pressing a handset button or lifting the handset off the base unit. Lighted handset keypad (KX-TC1701G/KX-TC1701F/KX-TC1701V ONLY) The handset dialing buttons will light when you press a button or lift the handset off the base unit, and flash when a call is received. The lights will go out about 10 seconds after pressing a button, lifting the handset or answering a call. Talk 00-01-30 CH12 22 Answering Calls When a call is received, the unit rings and the CALLER ID indicator on the base unit flashes quickly. If you subscribe to a Caller ID service, the calling party information will be displayed after the first ring (p. 26). Please wait until the second ring to answer a call in order to view the CALLER ID information. • You can also answer a call by pressing any dialing button (5) to ©, {*), or (#} (— Any Key Talk). OR If the handset is off the base unit, V. If on the base unit, just lift up. (This is not available when the Auto Talk feature is set to OFF. See page 18.) CALLER ID Indicator 23 Speed Dialer Storing Phone Numbers in Memory You can store up to 10 phone numbers in the handset. The dialing buttons ((o) to (9)) function as memory stations. The TALK indicator light must be off before programming. 1 Press I PROGRAM I. • The TALK indicator flashes. 2 Press SEARCH 0 (Yes key). 3 Enter a phone number up to 22 digits. • If you misdial, press I CLEAR I. Digits are erased from the right. 4 Press I AUTO I. Save AUTO# ? v=Next A-Yes Enter phone no. 3334444 AUTO=Save Select 0-9 to save in AUTO 24 3334444 Save in AUTO 1 g Press a memory station number ((o) to (9)). • A long beep sounds and the number is saved. • The handset will return to the stand-by mode. • To store other numbers, repeat steps 1 through 5. • To cancel during programming, press I PROGRAM! or [EXIT], then start from step 1. _ • If a pause is required for dialing, press IREDIAUPAUSEI where needed. Pressing I REDIAL/PAUSE I counts as one digit (p. 41). To erase a stored number 1 Press I PROGRAM I. • The TALK indicator flashes. Press SEARCH 0 (Yes key). Save AUTO# ? v=Next A=Yes Enter phone no. 3 4 Press I CLEAR I. Press [AUTOI. C Press the memory station number ^ ((o) to (9)) for the phone number to be erased. Dialing a Stored Number ■j Press (TALK). 2 Press [autoI. 0 Press the memory station number ((0] to (D). • The stored number is dialed. AUTO=Clear Select 0-9 to clear in AUTO Clear in AUTO 1 25 Caller ID Service This unit is compatible with a Caller ID service offered by your telephone company. After you subscribe to a Caller ID service, the calling party information will be displayed after the first ring. The unit can record information of up to 50 different callers, including the time and date received and the number of times called, in the Caller List. The Caller List information is sorted by the most recent to oldest call. When the 51st call is received, the first call is deleted. Using the list, you can automatically call back a caller. You can store the callers’ numbers from the Caller List into the Speed Dialer memory. If you subscribe to a Visual Call Waiting {Call Waiting ID) service, when a second call is received, the new caller’s name and phone number will be displayed (p. 41). How caller information is displayed when a call is received The display shows the caller’s name and number after the first ring. TINA ROBINSON 1-000-222-3333 After you answer the call, the display will show the length of the call and the present battery strength. 1 Talk. 00-0...