Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
• If you press within 5 seconds of playback, the previous message will be played. To rewind part of the message Press and hold (REPEAT/REW) until you reach the desired place. •At the beginning of the message, 3 beeps will sound. To skip/cue message To skip to the next message Press (skip/ff) briefly. To cue to part of the message Press and hold fSKlP/FF) until you reach the desired place. •The message will be heard at twice the normal speed. •At the end of the message, 3 beeps will sound. To stop operation Press [STOP], •To resume playback, press (new MESSAGE]. • If you do not press any button for 60 seconds or if you press [STOP] again, the unit will return to the stand-by mode. 30 From the Handset If someone else is in the room and you want to listen to the recorded messages privately, you can use the handset. 1 Handset: Press (PLAYBACK). •The number of new messages is heard on the handset. Base unit: To listen to new messages, press fNEV\r MESS AGE] briefly. To listen to all messages, press and hold (NEW MESSAGE) until playback starts. •The messages will be heard on the handset. •(REPEAT/REW), (SKIP/FF) and [ STOP) are also possible during playback (p. 30). When finished, press [PLAYBACK] or place the handset on the base unit. •You can also listen to messages without using the base unit. See page 42. Erasing Messages The unit will announce the remaining recording time after playback, if it is less than 5 minutes. New messages cannot be recorded when: —“Memory full” is heard. —“EED” is displayed. —the ANSWER ON indicator flashes rapidly. Erase some or all of the messages. We recommend you erase unnecessary messages after each playback. Erasing a specific message Press (ERASE) while the message you want to erase is being played. •The unit erases the message. •A short beep will sound and the unit will continue to play the next message. Erasing all messages All recorded messages, except the greeting message, can be erased at one time. -j Press [ ERASE 1. •“Press ERASE again to erase ANSWER ON Indicator 32 Pager Call This feature allows you to alert your pager when the unit records an incoming message. You can retrieve the message from a touch tone telephone (p. 36). First store the pager number, then set the unit to call the pager. The TALK indicator light must be off before programming. Storing a Pager Number If you use a 1-800 pager number, see the next page for the storing procedure. 1 Press (PROGRAM). •The TALK indicator flashes. TALK Indicator (PLAYBACK) 2 Press (PLAYBACK). •“P” is displayed on the base unit. 2 Press (#}. •“-" is displayed on the base unit. 4 0 Enter your pager number, and press (REDIAL/PAUSE) twice.* Enter the access code, if required by your pager company, and then press (REDIAL/PAUSE) twice again.* (2) Enter the call back number to be displayed on the pager (the telephone number where your unit is connected). (3) Press (#] if required by your pager company. • If you misdial, press (PROGRAM) and start again from step 1. •You can enter a total of 48 digits. ^ Press (PROGRAM). •A beep sounds. * Pager companies require a delay after the pager number and/or the access code is dialed. Contact your pager company regarding the required pause time. Pressing (REDIAL/PAUSE) once creates a 3.5 second delay and counts as one digit. • If the line has rotary or pulse service, press (TONE) between the pager number and (REDIAL/PAUSE) in step 4. Pager Call Storing a 1-800 pager number If you use a 1-800 pager number with a PIN code, store the pager number as follows. 1 Press (PROGRAM •The TALK indicator flashes. Press I PLAYBACK]. •“P” is displayed on the base unit. Press (#). is displayed on the base unit. © Enter the 1-800 pager number, and press [REDIAL/PAUSE] 3 times.* © Enter the PIN code, and press (REDtAL/PAUSE) twice * (3) Enter the call back number to be displayed on the pager (the telephone number where your unit is connected). @ Press (#] if required by your pager company. • If you misdial, press (PROGRAM] and start again from step 1. •You can enter a total of 48 digits. (REDIAL/PAUSE] PLAYBACK] Press [PROGRAM], •A beep sounds. * Pager companies require a delay after the pager number and the ■ PIN code are dialed. Contact your pager company regarding the required pause time. Pressing iREDIAL/PAUSE] once creates a i 3.5 second delay and counts as one digit. • If the line has rotary or pulse service, press [TONE) between the pager number and (REDIAL/PAUSE] in step 4. •Alphanumeric voice dispatch pager services will not work with this function. 34 To confirm the stored pager number Press (TALK) * (AUTO) * ®. •The unit dials the stored pager number. • If the pager does not beep, check your pager by calling it manually to ensure it works. Then start again from step 1 to store the pager number. To erase the stored pager number Press [PROGRAM) * (PLAYBACK) ® * (PROGRAMI. •The pager call mode will automatically ret...